molecalculator

Moles & Molar Mass

Dilution Ratio Calculator: How to Work It Out

Calculator No. 01-6051 · Updated · Formula and assumptions shown below

Stock solution to use 10.0 mL
Diluent to add
90.0 mL
= Final volume − Stock solution to use
Dilution factor
10.00
= Stock concentration ÷ Target concentration
Stock concentration
10 same units
Set in the form below
You enter
Stock concentration (same units), Target concentration (same units), Final volume (mL)
You get
Stock solution to use (mL), Diluent to add (mL), Dilution factor
Rounding
1 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator works out how much stock solution and diluent you need to reach a target concentration and final volume. Enter the stock concentration, target concentration, and final volume; it returns the stock volume and the amount of diluent to add. Use it for general laboratory planning, not for preparing anything for use in people or animals.

Formula

The standard dilution equation is C1V1 = C2V2. Rearranging it gives V1 = C2V2 / C1, the stock volume to use. The diluent volume is Vd = V2 − V1. The dilution factor is DF = C1 / C2.

  • C1 (cs) is the stock concentration.
  • C2 (ct) is the target concentration.
  • V1 (vs) is the volume of stock solution, in mL.
  • V2 (vf) is the desired final solution volume, in mL.
  • Vd (vd) is the calculated diluent volume, in mL.
  • DF is the dilution factor; it has no units.

The calculator requires both concentrations to use the same units—for example, both in mol/L or both in mg/mL. The dilution factor is a ratio, not a concentration. The expression includes a validity check: if the target concentration is higher than the stock concentration, the stock volume result is marked “Cannot compute,” because simple dilution cannot concentrate a solution.

Worked Example

Using the calculator defaults: stock concentration = 10 same-units, target concentration = 1 same-unit, and final volume = 100 mL.

  1. Calculate stock volume: V1 = C2 × V2 / C1 = 1 × 100 / 10 = 10.0 mL.
  2. Calculate diluent volume: Vd = 100 − 10 = 90.0 mL.
  3. Calculate the dilution factor: DF = 10 / 1 = 10, or a 1:10 final dilution relative to the stock.

For a practical preparation, measure 10.0 mL of stock and add diluent until the final solution volume reaches 100 mL. This is not necessarily the same as adding exactly 90.0 mL of solvent: volumes may not be additive, and the final-volume instruction is the more reliable one when precision matters.

Assumptions

  • The stock and target concentrations refer to the same substance and use compatible units.
  • The stock is homogeneous, and the solute remains stable and dissolved during dilution.
  • The target is no greater than the stock concentration, and the final volume is at least the stock volume.
  • The calculation uses the stated final solution volume; it does not account for contraction, expansion, reaction, or losses during transfer.

What You’ll Need

  • The stock concentration and the target concentration, expressed in the same units.
  • The desired final solution volume.
  • A calculator or this page’s calculator, plus a way to measure the required volumes accurately.
  • For bench work, appropriate personal protective equipment and the substance’s safety information.

Follow your lab method, the safety data sheet (SDS), and your supervisor. Check that the substance and procedure are appropriate for the intended laboratory work before handling it.

Step-by-Step

  1. Identify the stock concentration. Read the concentration from the solution label or validated preparation record. Make sure you know what the units mean, such as mol/L, g/L, or a percentage.
  2. Set the target concentration. Enter the concentration you want after dilution. Convert it to the same units as the stock first if necessary. For example, do not enter a stock in mg/mL and a target in g/L without converting one of them.
  3. Choose the final volume. Enter the total volume of finished solution you need, not the amount of diluent. The calculator’s volume inputs and outputs are in mL.
  4. Calculate the stock volume. The equation C1V1 = C2V2 assumes the amount of solute is conserved during dilution. The calculator rearranges it to find V1.
  5. Calculate the diluent amount. Subtract the stock volume from the final volume. If the result is negative or the stock volume exceeds the final volume, review the inputs; a simple dilution cannot achieve that combination.
  6. Measure and bring to final volume. Add the stock to a suitable vessel, then add the chosen diluent until the total volume reaches the specified final volume. Mix as directed by the applicable method.
  7. Label and verify. Record the substance, target concentration, final volume, date, and any required handling information. If concentration is critical, use the prescribed method to verify it rather than relying on arithmetic alone.

Common Mistakes

  • Mixing concentration units: the equation only works directly when both concentrations use the same units. Convert first; for instance, 1 g/L equals 1 mg/mL.
  • Confusing dilution factor with a ratio: a tenfold dilution has DF = 10 and can be written as 1:10 for final concentration relative to stock. In some protocols, “1:10” means one part stock plus ten parts diluent, which produces eleven total parts. State the convention explicitly.
  • Adding diluent as if volumes always add exactly: for accurate work, make up to the final volume rather than assuming stock volume plus solvent volume equals the intended total.
  • Rounding too early: calculate with unrounded values, then round to the resolution of your measuring equipment. A displayed decimal place does not guarantee that the volume can be measured accurately to that precision.
  • Trying to dilute to a higher concentration: dilution lowers concentration. Use a more concentrated stock or a separately validated concentration method when appropriate.
  • Ignoring stock uncertainty or labels: an incorrect or degraded stock concentration makes the calculated result unreliable. Confirm the solution identity, concentration, and expiry or stability status as required by your procedure.

Tips

  • Write the units beside each value before calculating. This makes incompatible inputs easier to catch.
  • Use a final volume that is practical to measure. If the required stock volume is below the reliable range of available equipment, consider a larger batch or a validated serial dilution.
  • For a serial dilution, calculate each stage separately. The overall dilution factor is the product of the individual stage factors; errors at one stage carry forward.
  • Keep a record of the formula, input values, units, and rounding. This makes the preparation reproducible.
  • For percentage concentrations, clarify whether the percentage is mass per volume, volume per volume, or mass per mass. Those definitions are not interchangeable.

Troubleshooting

The calculator says “Cannot compute.” Check that the target concentration does not exceed the stock concentration and that the concentrations are positive and in the same units. If the target is higher, dilution alone cannot reach it.

The calculated stock volume is too small to measure. Do not round it up casually, because that changes the final concentration. Use a suitable measurement range, increase the final batch volume, or plan a serial dilution with independently calculated stages.

The final concentration seems wrong. Recheck the stock label, unit conversions, the interpretation of any ratio notation, and whether you brought the mixture to final volume. Also check for transfer losses, evaporation, incomplete mixing, or chemical instability if relevant.

You added too much diluent. The solution is now more dilute than planned. Do not guess at a correction. Recalculate from the actual total volume and concentration if known, or prepare a fresh solution according to the approved method.

Frequently Asked Questions

What does a 1:10 dilution mean?
It commonly means the final solution is one-tenth the stock concentration, or a dilution factor of 10. Because some protocols use the notation to mean one part stock plus ten parts diluent, define the convention before preparing it.

How do I calculate the dilution factor?
Divide the stock concentration by the target concentration: DF = C1/C2. If stock is 10 units and target is 1 unit, the factor is 10.

Can I use different units for stock and target?
Not directly. Convert one concentration so both use the same unit before applying the equation.

Is diluent volume the same as final volume?
No. The final volume includes the stock solution. Diluent volume is approximately final volume minus stock volume, but precise preparations are usually brought up to the final-volume mark.

How do I make a dilution too small to measure accurately?
Use a larger final volume or a validated serial dilution, then calculate each step and multiply the stepwise dilution factors to check the overall result.

Related

Formula used
in cs | Stock concentration | same units | 10 | 0
in ct | Target concentration | same units | 1 | 0
in vf | Final volume | mL | 100 | 0
out vs | Stock solution to use | mL | ct * vf / cs | 1
out vd | Diluent to add | mL | vf - vs | 1
out df | Dilution factor | - | cs / ct | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →