molecalculator

Moles & Molar Mass

Log Base e on a Scientific Calculator

Calculator No. 01-6727 · Updated · Formula and assumptions shown below

Natural logarithm ln(x) 1.000000
Positive number x
2.718281828
Set in the form below
You enter
Positive number x
You get
Natural logarithm ln(x)
Rounding
6 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

To calculate log base e on a scientific calculator, use the ln key: ln(x) means loge(x), also called the natural logarithm. Enter a positive number and apply ln to get its natural logarithm; this page’s calculator evaluates ln(x) and reports the result.

Formula

The natural logarithm of a positive number x is the exponent y such that ey = x. In symbols, y = ln(x) = loge(x). Here, x is the input number (dimensionless for ordinary calculator use), e is Euler’s number, approximately 2.718281828, and y is the output exponent.

The calculator evaluates ln(x) directly. Its input must be greater than zero: ln(0) and the natural logarithm of a negative real number are undefined in the real-number system used by a standard scientific calculator.

Worked Example

Using the calculator’s default input, x = 2.718281828:

  1. Start with y = ln(x).
  2. Substitute the default: y = ln(2.718281828).
  3. Because 2.718281828 is a rounded value of e, y ≈ 1.000000.

The calculator displays 1.000000 to six decimal places. Since the input is a decimal approximation to e rather than the exact mathematical constant, the unrounded result is very close to 1, not necessarily exactly 1.

Assumptions

  • The input is a positive real number, not zero or a negative value.
  • The calculation uses the natural logarithm, base e, and does not require a physical unit conversion.
  • The default is a decimal approximation of e, so rounding can cause a tiny difference from exactly 1.

Where to Find and Use the ln Key

On most scientific calculators, ln is printed on a key, just as log is. The ln key calculates log base e; the log key usually calculates base 10. The exact key sequence depends on the calculator’s design and whether it uses immediate execution or an expression display.

  • Expression-entry models: press ln, type the value, close the parentheses if needed, then press equals. For example, enter ln(5) and evaluate it.
  • Value-first models: type 5, press ln, and read the displayed result.
  • Parentheses: if the screen shows an open ln( expression, make sure the input is inside the parentheses and close them before evaluating when required.

Follow the order shown on your calculator’s display or in its manual rather than assuming every model accepts the same key sequence. If the calculator has a two-line display, checking the expression before pressing equals can help catch a misplaced value or missing parenthesis.

What a Natural Logarithm Means

A logarithm answers an inverse question about exponentiation. Since e1 = e, ln(e) = 1. Since e0 = 1, ln(1) = 0. And because e2 is about 7.389, ln(7.389) is about 2. These are useful checks for whether you have selected the right function and entered the value correctly.

For positive inputs below 1, ln(x) is negative. For instance, ln(0.5) is approximately −0.693147. This is not an error: e raised to a negative power is a positive fraction. For inputs greater than 1, ln(x) is positive. The function increases continuously, but slowly: multiplying x by e increases ln(x) by exactly 1.

Natural logarithms appear in mathematics and science whenever a quantity changes exponentially or a relationship is naturally expressed using e. The calculator does not decide whether a logarithm is appropriate for a particular model; it only evaluates the mathematical function you request.

ln Versus log and Change of Base

The distinction between ln and log is the base. In common scientific-calculator notation, ln(x) means loge(x), while log(x) usually means log10(x). For example, log(100) = 2 in base 10, whereas ln(100) ≈ 4.605170. Check your calculator’s documentation if it uses a different convention or offers a separate base-entry function.

If a calculator lacks an ln key but has a base-10 log key, use the change-of-base identity:

loge(x) = log10(x) / log10(e).

On a calculator, this can be entered as log(x) ÷ log(e), using the same log function in both places. The ratio works because changing the logarithm’s base multiplies both numerator and denominator by the same constant. If the device has neither a logarithm function nor a reliable way to evaluate this expression, use a suitable calculator rather than estimating a scientific result by hand.

Common Errors and Limits

  • Choosing log instead of ln: these generally use different bases. Confirm the key label before evaluating.
  • Entering zero or a negative number: the real-valued natural logarithm is defined only for x > 0. A domain error or invalid-input message is expected otherwise.
  • Misreading a negative answer: an output below zero is valid when the input lies between 0 and 1.
  • Parentheses or key order: a calculator may evaluate a value before or after the ln key, depending on its interface. Review the displayed expression.
  • Rounding too early: retain the calculator’s digits during intermediate steps, then round the final answer to the precision appropriate for the problem.

Some calculators can handle complex numbers, where logarithms of negative values can be defined with additional conventions. That is a different calculation from the ordinary real-valued ln function described here; do not treat a complex-mode result as an ordinary real logarithm.

Frequently Asked Questions

What button is log base e on a scientific calculator?
Press ln. It is the standard key for the natural logarithm, meaning logarithm to base e.

Is ln the same as log?
Not usually on a scientific calculator. ln is base e; log commonly means base 10. The labels and conventions can vary, so check the calculator’s guide if uncertain.

How do I calculate ln(5)?
Use the ln function with 5 as its input. The result is approximately 1.609438.

Why does my calculator show an error for ln(0)?
There is no finite real number y for which ey = 0. The natural logarithm is defined for positive inputs only, so ln(0) is undefined.

Can I find ln without an ln key?
Yes, if the calculator has a base-10 log key: calculate log(x) ÷ log(e). Use the same log function in both parts of the ratio.

Related

Formula used
in x | Positive number x | - | 2.718281828 | 0
out y | Natural logarithm ln(x) | - | ln(x) | 6

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →