molecalculator

Moles & Molar Mass

Percent to Molarity Calculator: Formula and Examples

Calculator No. 01-5976 · Updated · Formula and assumptions shown below

Molarity 0.1711 mol/L
Concentration in millimolar
171.12 mM
= Molarity × 1000
Percent basis
w/v
Set in the form below
Percent concentration
1 %
Set in the form below
You enter
Percent basis, Percent concentration (%), Molar mass (g/mol), Solution density (g/mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A percent-to-molarity calculator converts a solution’s percent concentration into molarity, the number of moles of solute per liter of final solution. Enter the percent, its basis, the solute’s molar mass, and—when needed—solution density; the calculator returns mol/L and can also show mM.

Formula

For percent weight/volume (% w/v), molarity is (percent × 10) ÷ molar mass. For percent weight/weight (% w/w), molarity is (percent × density in g/mL × 10) ÷ molar mass. The calculator’s basis selector chooses the applicable expression.

  • Percent is the numerical percentage, such as 1 for 1%, not 0.01.
  • Molar mass is the solute’s mass per mole, in g/mol.
  • Density is the solution’s density, in g/mL; it is used for % w/w and ignored for % w/v.
  • Molarity is in mol/L. The factor 10 converts grams per 100 mL into grams per liter for % w/v; for % w/w it converts grams per 100 g of solution using density in g/mL.
  • Millimolar concentration is molarity × 1,000, since 1 mol/L = 1,000 mmol/L (mM).

For % w/v, a stated percentage means grams of solute per 100 mL of final solution. Thus, multiplying the percentage by 10 gives grams per liter; dividing by g/mol gives mol/L. For % w/w, the percentage means grams of solute per 100 g of solution. Density converts those 100 g of solution into its volume, which is why density is necessary.

Worked Example

Using the defaults—1% w/v, molar mass 58.44 g/mol, and density 1.00 g/mL—the density is not used. The % w/v calculation is:

1% w/v = 1 g per 100 mL of final solution.

1 g per 100 mL × 1,000 mL/L = 10.000 g/L.

10.000 g/L ÷ 58.44 g/mol = 0.1711157 mol/L, which rounds to 0.1711 mol/L.

In millimolar units, 0.1711157 mol/L × 1,000 = 171.1157 mM, or 171.12 mM.

How to Use the Calculator

  1. Choose the basis printed on the concentration information: % w/v or % w/w. Do not infer the basis from the number alone.
  2. Enter the percent as a number. For example, enter 5 for 5%, not 0.05.
  3. Enter the solute’s molar mass in g/mol. Use the formula or a reliable reference for the exact compound and chemical form.
  4. For % w/w, enter the density of the solution in g/mL at the relevant temperature. For % w/v, density does not affect the result.
  5. Read molarity in mol/L; use the mM output when a smaller concentration unit is more convenient.

A percent label may use a third convention, % v/v (volume of liquid solute per volume of solution). This calculator does not convert % v/v. That conversion generally needs the solute’s density and molar mass, and may need additional information about how volumes combine. Do not treat % v/v as either % w/v or % w/w.

Choosing the Right Inputs

Molar mass depends on the substance’s chemical formula and form. For example, a salt’s anhydrous form and its hydrate have different molar masses; using the wrong form changes the result. For a pure compound, calculate molar mass from its formula using standard atomic weights or consult a dependable chemical reference. If the stated concentration is for a mixture or commercial solution, confirm which component the percentage describes.

Density is a property of the solution, not automatically the density of pure water. It can change with concentration and temperature. Use a density appropriate to the solution and conditions. Assuming 1.00 g/mL for a % w/w solution may be a rough approximation for some dilute aqueous solutions, but it is not generally exact and can be substantially wrong for concentrated or nonaqueous solutions.

Common Errors and Limits

  • Confusing percent bases: 5% w/v means 5 g per 100 mL of solution; 5% w/w means 5 g per 100 g of solution. Their molarities are not necessarily equal.
  • Using solvent volume: the denominator for molarity is the final solution volume, not the volume of solvent initially measured. A labeled % w/v is defined per final solution volume.
  • Mixing units: enter molar mass in g/mol and, for % w/w, density in g/mL. A density in kg/L has the same numerical value as g/mL, but other units need conversion.
  • Rounding too early: keep several digits through the calculation and round the final answer to a precision supported by the inputs. Extra calculator digits do not make uncertain density or concentration data more accurate.
  • Assuming chemical behavior: this conversion gives analytical molarity from the stated amount of solute. It does not account for reaction, degradation, purity, or dissociation into ions. For an ionic compound, molarity of the compound is not automatically the molarity of each ion.

The equations assume the percent basis is correctly identified and that the supplied molar mass and density represent the actual substance and solution. They perform unit conversion only; they do not determine whether a concentration is chemically stable, safe, or suitable for an experiment. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

Frequently Asked Questions

How do I convert percent to molarity?
First identify whether the percent is w/v or w/w, then divide the solute mass per liter by its molar mass. For % w/v, use percent × 10 ÷ molar mass; for % w/w, include solution density: percent × density × 10 ÷ molar mass.

Can I convert percent to molarity without density?
Yes for % w/v, because its definition already gives grams per volume of final solution. For % w/w, density is needed to convert solution mass into solution volume.

Is 1% the same as 1 molar?
No. Percent describes a mass or volume ratio, while molarity describes moles per liter. The conversion depends on the percent basis and the solute’s molar mass, and for % w/w it also depends on density.

Can I use this calculator for percent by volume?
No. The calculator supports % w/v and % w/w only. A % v/v conversion requires appropriate volume-based information and may require density and other assumptions.

What is the difference between molarity and millimolar?
They express the same concentration at different scales: 1 mol/L equals 1,000 mM. Divide mM by 1,000 to get mol/L, or multiply mol/L by 1,000 to get mM.

When This Conversion Is Useful

Percent concentrations are common on solution labels and in preparation notes, while molarity is useful for stoichiometric calculations and comparing amounts of different compounds. Converting between them makes those forms easier to relate, provided the percent convention and physical data are known. When a source omits the basis, density, or chemical form needed for a reliable conversion, check the original specification rather than treating an assumed value as exact.

Related

Formula used
sel basis | Percent basis | w/v=1, w/w=2
in pct | Percent concentration | % | 1 | 0 | 100
in mm | Molar mass | g/mol | 58.44 | 0.000001
in den | Solution density | g/mL | 1.00 | 0.000001
out c | Molarity | mol/L | (basis * pct * 10 / mm) + (1 - basis) * (pct * den * 10 / mm) | 4
out cm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →