molecalculator

Moles & Molar Mass

Table of Equivalent Weights & How to Use It

Calculator No. 01-6952 · Updated · Formula and assumptions shown below

Equivalent weight 49.0395 g/eq
Molar mass of substance
98.079 g/mol
Set in the form below
n-factor (H⁺, e⁻, or charge)
2
Set in the form below
You enter
Molar mass of substance (g/mol), n-factor (H⁺, e⁻, or charge)
You get
Equivalent weight (g/eq)
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

An equivalent weight table lists the mass of a substance that reacts with or supplies one mole of hydrogen ions (H⁺) in an acid-base reaction, one mole of electrons in a redox reaction, or one mole of cations/anions in a precipitation reaction. You enter the substance’s molar mass and its n-factor (number of H⁺, electrons, or charge units transferred), and the calculator gives the equivalent weight in grams per equivalent. This page explains the concept, shows you how to compute it, and provides a practical tool for common laboratory calculations.

Formula

The equivalent weight (EW) is defined as:

EW = Molar mass (M) ÷ n-factor (n)

  • M – molar mass of the substance in grams per mole (g/mol). For a compound, this is the sum of the atomic weights of its constituent atoms.
  • n – the number of reactive units per molecule or formula unit. For acids, it is the number of ionizable H⁺ ions; for bases, the number of OH⁻ ions; for redox agents, the number of electrons transferred per molecule; for salts, the total positive or negative charge in the formula.
  • EW – equivalent weight in grams per equivalent (g/eq).

The unit “equivalent” (eq) is an amount of substance that reacts with one mole of H⁺, one mole of electrons, or one mole of a singly charged ion.

Worked Example

Using the default values in the calculator: sulfuric acid (H₂SO₄) has a molar mass of 98.079 g/mol and an n-factor of 2 (it can donate two H⁺ ions).

Step 1: Write down the formula: EW = M / n

Step 2: Substitute the values: EW = 98.079 g/mol ÷ 2

Step 3: Calculate: EW = 49.0395 g/eq

Rounded to four decimal places, the equivalent weight of H₂SO₄ is 49.0395 g/eq. This matches the calculator’s output.

Assumptions

  • The substance is pure and the molar mass is accurate.
  • The n-factor is correctly determined for the specific reaction being considered.
  • The reaction goes to completion (no side reactions).
  • For acids and bases, complete dissociation is assumed unless otherwise stated.

Background: Why Equivalent Weights Matter

Equivalent weights were introduced in the 19th century, before the modern concept of the mole was fully established. They allowed chemists to compare reacting amounts of different substances without knowing molecular formulas. For example, to neutralize 1 gram of NaOH, you needed to know how many grams of HCl would react with it. Equivalent weights made that calculation straightforward: the equivalent weight of NaOH is 40.00 g/eq (molar mass 40.00, n=1), and the equivalent weight of HCl is 36.46 g/eq (molar mass 36.46, n=1). So 40.00 g of NaOH reacts with 36.46 g of HCl.

Today, equivalent weights are still used in titration calculations, in normality (N) solutions, and in electrochemistry. Normality is defined as equivalents per liter of solution: N = (mass in g) / (equivalent weight × volume in L). Many analytical chemistry procedures, especially in water testing and clinical labs, still report concentrations in normality.

How to Determine the n-Factor

The n-factor depends on the type of reaction. Here are the general rules:

  • Acids: The number of H⁺ ions a molecule can donate. For HCl, n=1; for H₂SO₄, n=2; for H₃PO₄, n=3 (in complete neutralization).
  • Bases: The number of OH⁻ ions a formula unit can donate. For NaOH, n=1; for Ca(OH)₂, n=2; for Al(OH)₃, n=3.
  • Redox reactions: The number of electrons transferred per molecule. For KMnO₄ in acidic solution (Mn⁷⁺ → Mn²⁺), n=5; in neutral/basic solution (Mn⁷⁺ → Mn⁴⁺), n=3. For K₂Cr₂O₇ (Cr⁶⁺ → Cr³⁺, two Cr atoms), n=6.
  • Salts (precipitation): The total positive or negative charge in the formula. For NaCl, n=1; for CaCO₃, n=2; for Al₂(SO₄)₃, n=6 (because 2 Al³⁺ = 6 positive charges).

For a given substance, the n-factor can change with the reaction. For example, phosphoric acid (H₃PO₄) can donate 1, 2, or 3 H⁺ ions depending on the titration endpoint. Always specify the reaction context.

Common Mistakes and How to Avoid Them

  • Using the wrong n-factor: For redox reactions, you must balance the half-reaction to count electrons. For KMnO₄, using n=5 in a basic solution is wrong; it should be 3.
  • Confusing molar mass with equivalent weight: They are equal only when n=1. For H₂SO₄, the molar mass is 98 g/mol but the equivalent weight is 49 g/eq.
  • Unit mix-ups: Equivalent weight is in grams per equivalent, not grams per mole. When calculating normality, ensure volume is in liters.
  • Rounding too early: Keep at least 4 significant figures in intermediate steps to avoid errors in the final answer.

Practical Applications

Equivalent weights are used in several laboratory calculations:

  • Preparing normal solutions: To make 1 L of 1 N H₂SO₄, weigh out 49.04 g of H₂SO₄ (not 98.08 g).
  • Titration calculations: The equivalence point is reached when milliequivalents of acid = milliequivalents of base. This simplifies calculations because you don’t need to balance the full equation.
  • Water hardness: Hardness is often expressed in equivalents of CaCO₃. The equivalent weight of CaCO₃ is 50.05 g/eq (molar mass 100.09, n=2).
  • Electroplating and batteries: Faraday’s law uses equivalents: mass deposited = (molar mass × current × time) / (n × Faraday constant).

Limitations of Equivalent Weights

The concept of equivalent weight is reaction-specific, which is both its strength and its weakness. A single substance can have multiple equivalent weights depending on the reaction. For example, potassium permanganate has an equivalent weight of 31.61 g/eq in acid (158.04/5) but 52.68 g/eq in neutral solution (158.04/3). This ambiguity is why modern chemistry prefers molarity and moles for general work, but normality remains useful in specific analytical contexts.

Another limitation: equivalent weights assume complete reaction and ideal behavior. In real solutions, activity coefficients and incomplete dissociation can affect results. For precise work, always use molarity and stoichiometry, and verify with standards.

Frequently Asked Questions

What is the difference between equivalent weight and molar mass?

Molar mass is the mass of one mole of a substance (in g/mol). Equivalent weight is the mass of a substance that reacts with one mole of H⁺, e⁻, or charge. They are equal only when the n-factor is 1. For example, HCl has the same molar mass and equivalent weight (36.46), but H₂SO₄ has a molar mass of 98.08 and an equivalent weight of 49.04.

How do I find the equivalent weight of a salt?

For a salt, the n-factor is the total positive or negative charge in the formula. For NaCl, it’s 1; for CaCl₂, it’s 2 (Ca²⁺); for Fe₂(SO₄)₃, it’s 6 (2 Fe³⁺ = 6 positive charges). Divide the molar mass by that number.

Can equivalent weight be used for redox reactions?

Yes. The n-factor is the number of electrons transferred per molecule. For example, in acidic solution, KMnO₄ gains 5 electrons (Mn⁷⁺ to Mn²⁺), so its equivalent weight is molar mass / 5. You must balance the half-reaction to determine the correct n.

What is normality and how is it related to equivalent weight?

Normality (N) is equivalents per liter of solution. To prepare a 0.1 N solution, you weigh out 0.1 × equivalent weight (in grams) and dissolve to 1 L. For a 0.1 N H₂SO₄ solution, that’s 0.1 × 49.04 = 4.904 g/L.

Why do some substances have more than one equivalent weight?

Because the n-factor depends on the reaction. Phosphoric acid can donate 1, 2, or 3 H⁺ ions, giving equivalent weights of 98.00, 49.00, and 32.67 g/eq respectively. Always specify the reaction conditions.

Is equivalent weight the same as gram equivalent?

Yes, they are often used interchangeably. A gram equivalent is the mass in grams numerically equal to the equivalent weight. For example, 49.04 g of H₂SO₄ is one gram equivalent.

Safety and Lab Practice

When preparing solutions or performing titrations, always follow your lab’s standard operating procedures, the safety data sheet (SDS) for each chemical, and your supervisor’s instructions. Wear appropriate personal protective equipment (gloves, goggles, lab coat). For strong acids and bases, add acid to water slowly while stirring to avoid splashing. Never pipette by mouth. This calculator is for study and lab planning purposes only; always verify your calculations with a second method or a standard reference.

Related

Formula used
in m | Molar mass of substance | g/mol | 98.079 | 0
in nf | n-factor (H⁺, e⁻, or charge) | - | 2 | 1
out ew | Equivalent weight | g/eq | m / nf | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →