The C1V1 = C2V2 formula is commonly called the dilution equation or the dilution formula. In formal chemistry texts it is also known as the conservation of moles equation, because it states that the number of moles of solute remains unchanged when a solution is diluted by adding more solvent.
Formula
In symbols, the dilution equation is written as:
C1V1 = C2V2
Where:
- C1 = initial concentration (mol/L, g/L, % w/v, or any concentration unit)
- V1 = initial volume (L, mL, µL, or any volume unit)
- C2 = final concentration after dilution (same unit as C1)
- V2 = final total volume after dilution (same unit as V1)
The equation works because concentration × volume gives the amount of solute (in moles if concentration is molarity, or in grams if concentration is mass/volume). That amount does not change when you add pure solvent – you are only spreading the same solute over a larger volume.
Worked Example
Suppose you need to prepare 250 mL of a 0.200 mol/L NaCl solution from a 2.00 mol/L stock solution. How much stock do you need?
- Identify the values: C1 = 2.00 mol/L, C2 = 0.200 mol/L, V2 = 250 mL.
- Rearrange the formula to solve for V1: V1 = C2V2 / C1.
- Plug in the numbers: V1 = (0.200 mol/L × 250 mL) / 2.00 mol/L = 50.0 mL.
- Therefore, take 50.0 mL of the 2.00 mol/L stock and add enough solvent (water) to make the final volume 250 mL.
Notice that the volume units cancel because both V1 and V2 are in mL. The same calculation works if you use liters, as long as you are consistent.
Assumptions
- The amount of solute is conserved – no solute is added or removed during dilution.
- Volumes are additive (true for most dilute aqueous solutions, but not for concentrated acids or alcohols where volume contraction occurs).
- The concentration units are the same on both sides of the equation.
- Temperature remains constant – molarity changes with temperature because volume changes, though the effect is small for most lab work.
When to Use C1V1 = C2V2
This formula is used whenever you dilute a concentrated stock solution to a lower concentration. Typical situations include:
- Preparing a standard solution from a stock solution in analytical chemistry.
- Making a working concentration of a buffer, dye, or reagent from a concentrated stock.
- Diluting a commercial acid (like 12 M HCl) to a safer or usable concentration.
- Serial dilutions in microbiology or biochemistry – each step uses the same equation.
It applies to any concentration unit: molarity (mol/L), normality (eq/L), mass/volume percent (g/100 mL), or even absorbance units, as long as the unit is the same on both sides.
How to Choose the Right Values
The key is to decide which of the four variables you are solving for. Usually you know the stock concentration (C1), the desired final concentration (C2), and the final volume you want (V2). You then solve for V1, the volume of stock to take.
Always use the same unit for C1 and C2, and the same unit for V1 and V2. If you mix liters and milliliters, the answer will be off by a factor of 1000. A common trick is to keep volumes in mL and concentrations in mol/L – the product C×V then gives millimoles, which is fine as long as both sides use the same product unit.
Common Mistakes and Misconceptions
- Using V2 as the volume of solvent added. V2 is the final total volume (stock + solvent). If you add 100 mL of water to 50 mL of stock, V2 is 150 mL, not 100 mL.
- Mixing concentration units. C1 in mol/L and C2 in g/L will give a nonsense result. Convert first.
- Forgetting that molarity is temperature-dependent. If you need high precision, prepare the solution at the temperature you will use it.
- Assuming volumes are strictly additive. For dilute aqueous solutions this is fine, but mixing 50 mL ethanol with 50 mL water gives about 96 mL, not 100 mL.
- Thinking the formula only works for molarity. It works for any concentration unit where amount = concentration × volume.
Comparison with Other Dilution Formulas
There are other formulas you might encounter:
- Serial dilution factor: If you dilute 1:10 repeatedly, each step multiplies the previous concentration by 0.1. The final concentration after n steps is C_initial × (dilution factor)^n.
- Dilution factor (DF): DF = V2 / V1. For a 1:10 dilution, DF = 10. This is just a rearrangement of C1V1 = C2V2.
- M1V1 = M2V2 is the same equation, just using M for molarity instead of C for concentration.
The C1V1 = C2V2 formula is the most general because it does not assume any particular concentration unit.
Limitations of the Formula
The formula assumes ideal behavior – that the volume of the final solution is exactly the sum of the volumes of stock and solvent. This is not true for:
- Concentrated strong acids (e.g., H2SO4) where volume contraction occurs.
- Mixtures of liquids with strong intermolecular interactions (e.g., ethanol and water).
- Solutions with high solute concentrations where molarity deviates from molality.
For precise work, always prepare dilutions in a volumetric flask and make up to the mark with solvent, rather than measuring out the calculated solvent volume. Also, always add acid to water (not water to acid) when diluting concentrated acids – this is a safety rule.
Frequently Asked Questions
What does C1V1 = C2V2 mean?
It means that the amount of solute (in moles or grams) before dilution equals the amount after dilution. C1V1 gives the amount in the stock, and C2V2 gives the amount in the final solution – they are equal because you only add solvent.
Can I use C1V1 = C2V2 for any concentration unit?
Yes, as long as C1 and C2 use the same unit (mol/L, g/L, % w/v, etc.) and V1 and V2 use the same unit (L, mL, etc.). The product C×V then represents the amount of solute in those units.
What if I add solvent to a volume of stock – is V2 the final volume or the added volume?
V2 is the final total volume. If you have 50 mL of stock and add 100 mL of water, V2 is 150 mL. Many mistakes come from using the added solvent volume as V2.
How do I prepare a 1:10 dilution using this formula?
A 1:10 dilution means the final concentration is 1/10 of the stock. Set C2 = C1/10. Then V1 = (C1/10 × V2) / C1 = V2/10. So if you want 100 mL final, take 10 mL stock and make up to 100 mL with solvent.
Does temperature affect C1V1 = C2V2?
Strictly, molarity changes with temperature because volume changes. However, for most lab purposes the effect is small. If you need high accuracy, use molality or prepare the solution at the working temperature.
Can I use this formula for serial dilutions?
Yes, each step of a serial dilution is a separate application of C1V1 = C2V2. For example, a 1:10 serial dilution repeated three times gives a final concentration of 0.001 × C_initial.