molecalculator

Moles & Molar Mass

Molarity Calculator: Find Solution Concentration

Calculator No. 01-6795 · Updated · Formula and assumptions shown below

Molarity 0.2000 mol/L
Concentration in millimolar
200.00 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
58.44 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This online molarity calculator finds a solution’s concentration in moles per liter (mol/L) from the solute mass, its molar mass, and the final solution volume. Enter those three values to get molarity and the equivalent concentration in millimolar (mM).

Formula

Molarity is the amount of dissolved solute, in moles, divided by the total volume of the solution, in liters:

M = n / V = (m / MM) / (VmL / 1000)

  • M is molarity in mol/L.
  • n is the amount of solute in moles, calculated as mass divided by molar mass.
  • m is solute mass in grams.
  • MM is the compound’s molar mass in grams per mole.
  • VmL is final solution volume in milliliters. Dividing by 1000 converts mL to L.

The second result uses 1 mol/L = 1000 mM. The calculator assumes the entered mass is the mass of the solute itself, not the mass of a hydrated form or a mixture unless that is the substance whose molar mass you enter.

Worked Example

Using the calculator’s default values—2.922 g of solute, a molar mass of 58.44 g/mol, and 250 mL final solution volume:

  1. Calculate moles: 2.922 g / 58.44 g/mol = 0.050000 mol.
  2. Convert final volume: 250 mL / 1000 = 0.250 L.
  3. Divide amount by volume: 0.050000 mol / 0.250 L = 0.2000 mol/L.
  4. Convert to millimolar: 0.2000 mol/L × 1000 = 200.00 mM, displayed as 200 mM.

The result is 0.2000 mol/L, or 200 mM. The calculation gives a concentration from the specified inputs; it does not measure a prepared solution.

Assumptions

  • The entered mass is pure solute with the stated molar mass.
  • The volume is the final solution volume, not the volume of solvent added before dissolving.
  • Mass and volume are measured in grams and milliliters, respectively, and the sample is treated as a uniform solution.
  • No temperature correction, activity correction, or chemical reaction during preparation is included.

When to Use a Molarity Calculator

Molarity is useful when a chemistry problem, experiment plan, or solution label describes concentration as moles of solute per liter of solution. This calculator is suited to cases where you know the solid or liquid solute’s mass, the compound’s molar mass, and the final volume. It can also check a hand calculation or convert a result to millimolar, a unit commonly used for relatively dilute concentrations.

It can help with classroom stoichiometry and general laboratory planning, but it cannot tell you how much solute to weigh when the target concentration and volume are the known values. That reverse calculation is m = M × V × MM, with volume in liters. For example, a target molarity of 0.200 mol/L in 0.250 L corresponds to 0.200 × 0.250 = 0.0500 mol; multiplying by the appropriate molar mass gives the required solute mass. For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.

How to Enter Values and Read the Result

  • Mass of solute: Enter the amount actually being counted as solute, in grams. If your balance reading is in milligrams, convert it to grams by dividing by 1000.
  • Molar mass: Use the molar mass for the correct chemical formula and chemical form, in g/mol. Include waters of crystallization when the material is a hydrate.
  • Final solution volume: Enter the solution’s total volume after the solute is dissolved and the volume is adjusted, in mL.

The first output is molarity in mol/L; the second is the same concentration in mM. Molarity is sometimes written with a capital M, where 1 M means 1 mol/L. Do not confuse it with molality, written as mol/kg, which uses the mass of solvent rather than solution volume.

Common Errors and Limits

The most consequential volume mistake is using the amount of solvent instead of the final solution volume. Dissolved material can change the total volume, so adding solute to 250 mL of water does not necessarily produce 250 mL of solution. In a standard preparation calculation, the intended volume is the final volume after dissolving and bringing the solution to its target.

Check the chemical form before trusting the molar mass. A hydrate has a different molar mass from its anhydrous compound, and a salt may have a different formula from the neutral compound. Purity also matters: if the weighed material contains impurities or has absorbed water, treating all its mass as pure solute can overstate the calculated concentration. This calculator does not correct for purity, density, temperature-dependent volume, or uncertainty in the measurements.

Finally, calculated molarity is not always the same as the concentration of a particular reactive species. A dissolved ionic compound may separate into ions, and acid–base reactions, complex formation, or precipitation can change the amounts of species present. The formula reports the formal amount of the entered solute per final solution volume; interpreting equilibrium concentrations requires additional chemical information.

Frequently Asked Questions

How do I calculate molarity from grams?
Divide the solute mass in grams by its molar mass in g/mol to get moles. Divide those moles by the final solution volume in liters. If volume is in mL, divide it by 1000 first.

Is molarity the same as mol/L?
Yes. Molarity is expressed in moles per liter; 1 M equals 1 mol/L. Millimolar is one-thousandth of a molar, so 1 mM equals 0.001 mol/L.

Do I use the solvent volume or final solution volume?
Use the final solution volume. It includes both solvent and dissolved solute, rather than just the liquid initially measured before dissolving.

Can I calculate molarity if I know the number of moles?
Yes. Divide moles by solution volume in liters: M = n/V. The calculator on this page instead derives moles from mass and molar mass.

Why does a hydrate need a different molar mass?
A hydrate’s formula includes water molecules associated with each formula unit. Those water molecules contribute to its mass, so use the molar mass of the hydrate actually weighed, not the anhydrous compound’s value.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →