molecalculator

Moles & Molar Mass

Clorox Dilution Table: Mix Ratios Explained

Calculator No. 01-7136 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This page explains the Clorox dilution table, showing how to mix bleach with water to get the right concentration for disinfecting, cleaning, and other tasks. You enter the desired bleach-to-water ratio or the percentage of sodium hypochlorite you need, and the calculator returns the exact amounts of bleach and water to mix. This is useful for everyday cleaning, lab disinfection, and any situation where you need a specific bleach concentration.

Formula

The dilution formula is the classic C1 × V1 = C2 × V2, where C is concentration and V is volume. For bleach, we want to find the volume of bleach (V1) needed to make a final volume (V2) at a target concentration (C2), given the bleach’s original concentration (C1).

Rearranged: V1 = (C2 × V2) / C1

  • C1 = concentration of the bleach you have (as a percentage, e.g., 8.25%)
  • C2 = desired final concentration (as a percentage, e.g., 0.5%)
  • V2 = total final volume of the solution (in mL)
  • V1 = volume of bleach to use (in mL)

Then, the water to add is simply V2 – V1.

Worked Example

Suppose you have a bottle of regular bleach (8.25% sodium hypochlorite) and you want to make 1000 mL (1 liter) of a 0.5% disinfecting solution.

  1. Identify the values: C1 = 8.25%, C2 = 0.5%, V2 = 1000 mL.
  2. Calculate the bleach volume: V1 = (0.5% × 1000 mL) / 8.25% = 500 / 8.25 = 60.606… mL.
  3. Round to 60.6 mL of bleach.
  4. Calculate the water: 1000 mL – 60.6 mL = 939.4 mL of water.

So, mix 60.6 mL of bleach with 939.4 mL of water to get 1 liter of 0.5% solution. The calculator above gives the same result.

Assumptions

  • The bleach concentration is exactly as labeled on the bottle (this can vary slightly with age and storage).
  • Volumes are additive (mixing 60.6 mL of bleach with 939.4 mL of water gives exactly 1000 mL). In practice, this is close enough.
  • The desired concentration is based on the percentage of sodium hypochlorite (NaOCl) in the solution, not the amount of available chlorine.

Understanding Bleach Concentrations

Household bleach is a solution of sodium hypochlorite (NaOCl) in water. The concentration is usually printed on the label as a percentage. Common values are:

  • Regular bleach: 8.25% sodium hypochlorite (this is the most common in the US).
  • Concentrated bleach: 6% (often sold in smaller bottles, but check the label).
  • Thick bleach: 3% (sometimes used for toilets, but less common for general disinfection).
  • Industrial bleach: 10-12% (used for heavy-duty cleaning, not for home use).

Always check the label of your specific bottle. The percentage is the key number you need for the dilution table.

How to Use the Dilution Table

Most official guidelines (like those from the CDC or WHO) give dilution ratios for a specific starting concentration, usually 8.25% or 5.25%. If your bleach is a different concentration, you must adjust the ratio. Here is how to read a typical table:

  • For disinfecting surfaces (0.5% solution): With 8.25% bleach, mix 1 part bleach with 16 parts water (1:16). That’s about 1/3 cup bleach per gallon of water.
  • For sanitizing food contact surfaces (0.1% solution): With 8.25% bleach, mix 1 part bleach with 82 parts water (1:82). That’s about 1.5 teaspoons per gallon.
  • For laundry (0.05% solution): With 8.25% bleach, mix 1 part bleach with 165 parts water (1:165). That’s about 1 tablespoon per gallon.

The table below shows the amounts for a 1-gallon (128 oz) batch, using 8.25% bleach:

Desired Concentration Bleach (mL) Water (mL)
0.1% 15.5 mL 112.5 mL
0.5% 77.5 mL 50.5 mL
1% 155 mL 0 mL (use as is)

Note: These are approximate because the table assumes 8.25% bleach. Use the calculator above for exact amounts with your specific bleach.

Common Mistakes and Misconceptions

One common mistake is using the ratio from a table without checking your bleach’s concentration. If you use 6% bleach when the table assumes 8.25%, your solution will be too weak. Another mistake is measuring by volume incorrectly: always use a liquid measuring cup, not a dry measuring cup, for bleach.

A major misconception is that more bleach is always better. Using too high a concentration can leave harmful residues, damage surfaces, and create irritating fumes. Stick to the recommended concentrations for the task.

Also, never mix bleach with ammonia or other cleaners, as this produces toxic chlorine gas. Always add bleach to water, not water to bleach, to avoid splashing.

Safety and Storage

Bleach is a strong oxidizer. Always work in a well-ventilated area. Wear gloves and eye protection if you are mixing large quantities. Never mix bleach with acids (like vinegar) or ammonia. Store bleach in its original container, away from heat and light. Bleach degrades over time, so it is best to use it within a few months of opening. For disinfection, the solution should be made fresh daily, as the active chlorine breaks down quickly in water.

Alternatives to Bleach

If you are looking for a less harsh disinfectant, consider hydrogen peroxide (3% solution) or quaternary ammonium compounds (often found in commercial disinfectants). These are effective against many pathogens and are less corrosive. However, bleach is one of the most effective and inexpensive disinfectants against a wide range of microorganisms, including bacteria, viruses, and fungi. For lab use, ethanol (70%) is also a common alternative, but it is flammable.

Frequently Asked Questions

What is the ratio of bleach to water for disinfecting?

For general disinfection of surfaces, the CDC recommends a 0.5% sodium hypochlorite solution. With 8.25% bleach, that is a 1:16 ratio (1 part bleach to 16 parts water). That translates to about 1/3 cup of bleach per gallon of water.

Can I use the same dilution for all surfaces?

No. Porous surfaces like wood may require a stronger solution, while food contact surfaces should be rinsed with potable water after disinfecting. Always follow the instructions for the specific surface and the official guidelines for the pathogen you are targeting.

How long does diluted bleach stay effective?

Diluted bleach solutions lose their disinfecting power quickly, often within 24 hours. It is best to prepare a fresh solution each day. Store it in a labeled, opaque container if you must keep it, but do not expect it to be effective after a few days.

What if my bleach is 6% instead of 8.25%?

You need to adjust the ratio. For a 0.5% solution, use 1 part 6% bleach to 12 parts water (1:12). To be precise, use the calculator above: enter 6% as the bleach type and 0.5% as the desired concentration.

Is it safe to mix bleach with hot water?

No. Hot water breaks down the sodium hypochlorite faster, releasing chlorine gas and reducing the disinfecting power. Always use cool or room-temperature water.

Can I use bleach to disinfect my drinking water?

Yes, but only in emergencies and with specific guidelines. The typical recommendation is 8 drops of 8.25% bleach per gallon of clear water, and 16 drops if the water is cloudy. Let it stand for 30 minutes. This is a last resort; use purified water if possible.

Related

Formula used
in sel | Bleach type | Regular (8.25%)=8.25, Concentrated (6%)=6, Thick (3%)=3
in f | Desired final concentration (%) | % | 0.5 | 0.01 | 10
in v | Total final volume | mL | 1000 | 1 | 100000
out bleach | Bleach needed | mL | (f / 100 * v) / (sel / 100) | 1
out water | Water to add | mL | v - bleach | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →