A saturated aqueous sodium chloride solution is about 6.1 mol/L (6.1 M) at room temperature, with the exact value depending on temperature and how concentration is defined. This calculator estimates molarity from the mass of dissolved NaCl and the final solution volume; it does not calculate the saturation limit itself.
Formula
Molarity is the amount of solute in moles divided by the final volume of solution in litres:
c = (m / M) / (V / 1000)
- c is molarity, in mol/L.
- m is the mass of sodium chloride, in grams.
- M is the molar mass of sodium chloride, 58.44 g/mol for this calculation.
- V is final solution volume, in millilitres. Dividing by 1000 converts mL to L.
The second output is the same concentration in millimolar: 1 mol/L = 1000 mM. The 58.44 g/mol value follows from the conventional atomic weights Na = 22.990 and Cl = 35.45 g/mol, rounded to 58.44 g/mol.
Worked Example
Using the calculator defaults—356 g NaCl, 58.44 g/mol, and 1000 mL final solution volume:
- Moles of NaCl = 356 g / 58.44 g/mol = 6.0917 mol.
- Convert the final volume: 1000 mL / 1000 = 1.000 L.
- Molarity = 6.0917 mol / 1.000 L = 6.0917 mol/L, which rounds to 6.0917 M.
- Millimolar concentration = 6.0917 × 1000 = 6092 mM, rounded to the nearest whole mM.
Assumptions
- The entered mass is pure sodium chloride and represents all dissolved solute.
- The entered volume is the final solution volume, not the amount of water used.
- This is a concentration calculation; it assumes no chemical reaction or loss of NaCl.
- The calculator does not account for temperature-dependent density, activity, or measurement uncertainty.
What “Saturated” Means for NaCl
A solution is saturated when it contains as much dissolved solute as can remain in equilibrium with undissolved solute under specified conditions. For sodium chloride in water near room temperature, solubility is roughly 36 g NaCl per 100 g water. That ratio is based on the mass of water, not the final volume of solution.
At about 20–25 °C, the saturated solution is commonly described as roughly 26% NaCl by mass and has a density around 1.2 g/mL. Combining these approximate properties gives a molarity near 6.1 mol/L. These figures are useful for orientation, but they are not exact universal constants: temperature, purity, and the particular solubility or density data used affect the result.
The default example is intentionally a direct molarity calculation, not a claim that every 356 g of salt forms exactly one litre of saturated solution. In practice, solution volume is not equal to water volume plus a simple salt volume: dissolved ions change the mixture’s volume. Use a measured final volume or a reliable density and composition value when precision matters.
Why the Calculator Is Not a Saturation Test
The formula converts mass and volume into molarity. It cannot decide whether a sample is saturated because that requires comparing the composition with the solubility limit at a stated temperature. For instance, 6.1 M is a reasonable approximate molarity for saturated brine near room temperature, but a solution at 6.1 M under substantially different conditions should not automatically be labelled saturated.
For an estimate from a mass-percent value and density, use the relation:
c = (mass fraction × density × 1000) / molar mass
Here density is in g/mL, molar mass in g/mol, and the factor 1000 converts millilitres to litres. If the solution is 26% NaCl by mass and its density is taken as 1.20 g/mL, then the estimate is (0.26 × 1.20 × 1000) / 58.44 ≈ 5.34 mol/L. This illustrates why approximate inputs matter: common reference descriptions and tabulated properties can yield different estimates. For a dependable value, use a consistent temperature-specific solubility and density source rather than mixing rounded figures.
Concentration Units and Common Mix-Ups
- Molarity (M): moles of solute per litre of final solution. It varies with temperature because liquid volume can expand or contract.
- Mass percent: grams of NaCl per 100 g of solution. It is not grams per 100 mL.
- Solubility by mass: often reported as grams of salt per 100 g of water. This is not the same denominator as mass percent of solution.
- Molality: moles of solute per kilogram of solvent. Unlike molarity, its denominator is solvent mass rather than solution volume.
A frequent error is to divide salt mass by the volume of water added. Molarity requires the final volume after the salt has dissolved. Another is to treat a saturated brine’s approximate molarity as an exact value regardless of temperature. Report the temperature and the concentration basis whenever the value is being used for laboratory calculations.
Using the Result and Practical Limits
Use the calculator for general solution arithmetic when you know dissolved NaCl mass and final solution volume. If you instead know an existing concentration and need to prepare a dilution, this calculator alone is not enough; the starting and target concentrations and final volume are needed. For saturated solutions, consult a temperature-specific solubility table, or use measured composition and density where appropriate.
Rounding should match the quality of the inputs. The example’s displayed four decimal places are a calculator convention, not a claim that the result is known to that precision: a mass entered as 356 g supports far fewer meaningful digits than 6.0917 suggests. Keep extra digits during intermediate calculations and round the reported answer to reflect actual measurement precision.
This is a general chemistry calculator, not a substitute for validated analytical data. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor. Avoid contact with eyes, and clean up salt spills to prevent slipping or damage to equipment.
Frequently Asked Questions
What is the molarity of saturated NaCl solution?
Near room temperature, a commonly used estimate is about 6.1 mol/L. The exact value depends on temperature and the underlying composition and density data.
How many grams of NaCl dissolve in 100 g of water?
Approximately 36 g near 20–25 °C. Solubility is temperature-dependent, and the figure is per 100 g of water, not per 100 g of finished solution.
Is saturated NaCl solution the same as 26% salt?
Not exactly as a universal statement. Saturated brine near room temperature is often approximated as about 26% NaCl by mass, but temperature and reference data affect the value.
Does 1 L of water make 1 L of saturated brine?
No. Adding and dissolving salt changes the mixture’s volume. Molarity uses the final solution volume, which must be measured or reliably determined.
Does NaCl solubility change much with temperature?
It changes less dramatically than the solubility of some salts, but it does change. Use a solubility value measured or tabulated for the relevant temperature when accuracy matters.
Related
Formula used
in m | Mass of NaCl | g | 356 | 0 in mm | Molar mass of NaCl | g/mol | 58.44 | 0.001 in v | Final solution volume | mL | 1000 | 0.001 out c | Molarity | mol/L | m / mm / (v / 1000) | 4 out cmm | Concentration in millimolar | mM | c * 1000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Liters to Cubic Meters: Conversion and Examples0.001000 m³
- Normal Cubic Meter to Liters Calculator1,000.00 L
- Qt to Liters Conversion: US and Imperial Quarts0.946353 L
- Meters to Liters Formula: Convert Length to Volume?1,000.000 L
- Meters to Litres: Why Length Alone Is Not Enough1,000.00 L
- Cubic Meters per Hour to Liters per Second0.2778 L/s