molecalculator

Moles & Molar Mass

Exponential Decay Half-Life Problems Explained

Calculator No. 01-6975 · Updated · Formula and assumptions shown below

Remaining amount 17.6777
Fraction remaining
0.1768
= 0.5^(Elapsed time ÷ Half-life)
Percent remaining
17.68 %
= 0.5^(Elapsed time ÷ Half-life) × 100
Initial amount
100
Set in the form below
You enter
Initial amount, Half-life (time units), Elapsed time (time units)
You get
Remaining amount, Fraction remaining, Percent remaining (%)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Exponential decay half-life problems ask you to find how much of a substance remains after a given time, or how long it takes to reach a certain amount, using the constant half-life of the decaying quantity. You enter the initial amount, the half-life, and either the elapsed time or the remaining amount, and the calculator returns the missing value. This page explains the math behind these problems and walks through real examples.

Formula

The standard exponential decay formula is:

A(t) = A₀ × (1/2)^(t / T½)

Where:

  • A(t) = amount remaining after time t (same unit as A₀)
  • A₀ = initial amount (any unit: grams, moles, counts, etc.)
  • t = elapsed time (any time unit: seconds, hours, years)
  • T½ = half-life (same time unit as t)

The exponent (t / T½) tells you how many half-lives have passed. For example, if t = 3 × T½, then the fraction remaining is (1/2)^3 = 1/8. The formula works for any positive values of t and T½, and it does not require t to be a whole-number multiple of the half-life.

Worked Example

Using the calculator defaults: A₀ = 100, T½ = 10 time units, t = 25 time units.

Step 1: Compute the number of half-lives: t / T½ = 25 / 10 = 2.5.

Step 2: Compute the fraction remaining: (1/2)^2.5 = 0.5^2.5.

Step 3: 0.5^2.5 = 0.1767767 (rounded to 4 decimals: 0.1768).

Step 4: Multiply by initial amount: 100 × 0.1767767 = 17.67767, which rounds to 17.6777.

So after 25 time units, 17.6777 units remain (about 17.68% of the original). The calculator shows the same result.

Assumptions

  • The decay follows a pure exponential law with a constant half-life.
  • The half-life is independent of the amount present (true for radioactive decay and many first-order chemical reactions).
  • There is no addition of new material during the decay period.
  • The initial amount is positive and the half-life is positive.

When to Use Half-Life Problems

Half-life problems appear in several fields:

  • Radioactive decay – determining how much of a radioisotope remains after a storage period, or how long until activity drops to a safe level.
  • Pharmacokinetics – estimating how long a drug stays in the body (though real drug elimination often involves multiple compartments).
  • Carbon dating – using the half-life of carbon-14 (about 5,730 years) to estimate the age of organic material.
  • Nuclear waste management – planning storage times for radioactive waste.
  • Chemical kinetics – for first-order reactions, the half-life is constant and independent of concentration.

In each case, the same formula applies, as long as the decay rate is proportional to the amount present.

How to Solve Different Types of Problems

Most textbook problems fall into three categories:

  1. Find the remaining amount – given A₀, T½, and t, use A(t) = A₀ × 0.5^(t/T½).
  2. Find the time elapsed – given A₀, A(t), and T½, rearrange to t = T½ × log₂(A₀ / A(t)). Using natural log: t = T½ × ln(A₀/A(t)) / ln(2).
  3. Find the half-life – given A₀, A(t), and t, rearrange to T½ = t / log₂(A₀ / A(t)).

For example, if a sample starts at 80 g and after 20 days only 10 g remain, the fraction remaining is 10/80 = 0.125 = (1/2)^3, so 3 half-lives have passed. Thus T½ = 20 days / 3 ≈ 6.67 days.

Common Mistakes and Misconceptions

  • Using the wrong base – The formula uses 0.5, not e. If you use e^(-λt) with λ = ln(2)/T½, you get the same answer, but mixing the two forms often leads to errors.
  • Unit mismatch – t and T½ must be in the same time unit. Convert minutes to hours, days to years, etc., before plugging in.
  • Forgetting that the fraction is exponential, not linear – After two half-lives, 25% remains, not 0%. After three, 12.5% remains.
  • Rounding too early – Round only at the final step. For example, 0.5^2.5 is 0.1767767, not 0.18.
  • Confusing half-life with mean life – The mean life (τ) is T½ / ln(2) ≈ 1.443 × T½. They are different.

Real-World Example: Carbon-14 Dating

Carbon-14 has a half-life of about 5,730 years. Suppose a bone fragment contains 25% of the carbon-14 that a living organism would have. How old is it?

Fraction remaining = 0.25 = (1/2)^2, so 2 half-lives have passed. Age = 2 × 5,730 = 11,460 years. If the fraction were 30%, you would use the logarithmic formula: t = 5,730 × ln(1/0.30) / ln(2) ≈ 5,730 × 1.204 / 0.693 ≈ 9,950 years. This shows how the formula handles non-integer half-lives.

Limitations of the Simple Model

The simple exponential decay model assumes a single decay process with a constant half-life. In reality:

  • Some substances decay through a chain (e.g., uranium-238 decays through many steps), so the overall activity depends on the decay of daughter products.
  • In biological systems, drug clearance often follows multi-compartment kinetics, so a single half-life may not describe the entire time course.
  • For chemical reactions, half-life is constant only for first-order reactions. For second-order reactions, the half-life depends on the initial concentration.
  • Environmental factors (temperature, pressure) can affect reaction rates, but not radioactive decay (which is essentially constant).

When solving problems, always check whether the situation truly follows first-order exponential decay.

Frequently Asked Questions

What is the difference between half-life and doubling time?

Half-life is the time for a decaying quantity to reduce to half its initial value. Doubling time is the time for a growing quantity to double. They are related: doubling time = T½ × ln(2) / ln(2) = T½ only if the growth rate equals the decay rate, which is not typical. For exponential growth, doubling time = ln(2)/growth rate constant.

Can half-life be used for any type of decay?

Half-life is defined for any process that follows first-order exponential decay. This includes radioactive decay, many chemical reactions (first-order), and some biological processes (like drug elimination). For processes that do not follow first-order kinetics, the half-life may change over time and the simple formula does not apply.

How do I find the decay constant from the half-life?

The decay constant λ is related to half-life by λ = ln(2) / T½. For example, if T½ = 10 days, λ = 0.6931 / 10 = 0.06931 per day. Then the decay formula can be written as A(t) = A₀ × e^(-λt).

What if the problem gives the decay rate as a percentage per year?

A percentage per year is not the same as the decay constant. If a substance decays at 5% per year, then after one year 95% remains. The half-life is found by solving 0.95 = 0.5^(1/T½), which gives T½ = ln(0.5)/ln(0.95) ≈ 13.5 years. The decay constant λ = -ln(0.95) ≈ 0.0513 per year.

Why does the calculator allow any unit for the initial amount?

Because the half-life formula is unit-agnostic for the amount. Whether you use grams, moles, or counts, the fraction remaining is the same. The calculator returns the remaining amount in the same unit you entered, so you can use any consistent unit.

Does the calculator work for negative time?

No, the calculator rejects negative elapsed time because it would imply going backward in time. The formula technically works for negative t (giving amounts larger than the initial), but that is not physically meaningful for decay problems.

For lab work involving radioactive materials or reactive chemicals, always follow your lab method, the safety data sheet (SDS), and your supervisor.

Related

Formula used
in m | Initial amount | - | 100 | 0
in hl | Half-life | time units | 10 | 0.000001
in t | Elapsed time | time units | 25 | 0
out rem | Remaining amount | - | m * 0.5^(t / hl) | 4
out frac | Fraction remaining | - | 0.5^(t / hl) | 4
out pct | Percent remaining | % | 0.5^(t / hl) * 100 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →