molecalculator

Moles & Molar Mass

Formula to Calculate Enthalpy: ΔH = ΔU + PΔV

Calculator No. 01-6868 · Updated · Formula and assumptions shown below

Enthalpy change (ΔH) 12.50 kJ
ΔH from ΔU + PΔV
10.20 kJ
Result, rounded to 2 decimal places
Heat absorbed at constant pressure (q_p)
12.5 kJ
Set in the form below
Change in internal energy (ΔU)
10 kJ
Set in the form below
You enter
Heat absorbed at constant pressure (q_p) (kJ), Change in internal energy (ΔU) (kJ), Pressure (kPa), Change in volume (ΔV) (L)
You get
Enthalpy change (ΔH) (kJ), ΔH from ΔU + PΔV (kJ)
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The most general formula to calculate enthalpy is H = U + PV, where U is internal energy, P is pressure, and V is volume. For a chemical reaction at constant pressure, the enthalpy change is ΔH = ΔU + PΔV, and in practice it is usually measured as the heat exchanged at constant pressure: ΔH = qp. This calculator works out the enthalpy change of a reaction from the internal energy change, pressure, and volume change, or from the heat absorbed at constant pressure.

Formula

Enthalpy (H) is a state function defined as the sum of a system’s internal energy (U) and the product of its pressure (P) and volume (V):

H = U + PV

For a process at constant pressure, the change in enthalpy is:

ΔH = ΔU + PΔV

where:

  • ΔH = enthalpy change (kJ, or J/mol for molar enthalpy)
  • ΔU = change in internal energy (kJ)
  • P = constant external pressure (kPa)
  • ΔV = change in volume (L)

When converting the pressure–volume term to kJ, use the conversion: 1 kPa·L = 1 J, so PΔV in kPa·L divided by 1000 gives kJ. At constant pressure, the enthalpy change equals the heat transferred to or from the system: ΔH = qp.

Worked Example

Using the calculator defaults: a reaction absorbs 12.5 kJ of heat at constant pressure. The internal energy increases by 10.0 kJ, the pressure is 101.325 kPa, and the volume expands by 2.0 L.

Step 1: Direct from heat at constant pressure:

ΔH = qp = 12.5 kJ

Step 2: From ΔU and PΔV:

PΔV = 101.325 kPa × 2.0 L = 202.65 kPa·L = 202.65 J = 0.20265 kJ

ΔH = ΔU + PΔV = 10.0 kJ + 0.20265 kJ = 10.20265 kJ ≈ 10.20 kJ

Notice the two results differ because the heat absorbed (12.5 kJ) includes both the internal energy change and the work done on the surroundings. In a constant-pressure calorimeter, the measured heat is the enthalpy change directly, so ΔH = 12.5 kJ.

Assumptions

  • The process occurs at constant pressure (common for reactions open to the atmosphere).
  • The only work done is pressure–volume work (no electrical, gravitational, or surface work).
  • The pressure is constant throughout the process.
  • For gases, ideal behavior is assumed when relating P, V, and temperature.
  • Heat capacities are taken as constant over the temperature range of interest.

When to Use ΔH = qp vs ΔH = ΔU + PΔV

The most common situation in chemistry is a reaction carried out in an open beaker or flask at atmospheric pressure. The heat measured by a simple calorimeter (like a coffee-cup calorimeter) is the enthalpy change, because the pressure is constant. In that case, ΔH = qp is the correct and simplest formula.

However, if you are given the change in internal energy (from a bomb calorimeter, which operates at constant volume) and you need the enthalpy change, you must add the PΔV term. For reactions involving gases, the volume change can be significant. For reactions involving only solids and liquids, the volume change is usually tiny, so ΔH ≈ ΔU.

For an ideal gas reaction at constant temperature, you can also use the relation ΔH = ΔU + ΔngasRT, where Δngas is the change in moles of gas. This is a shortcut that avoids measuring volume directly.

How to Read the Result

A negative ΔH means the reaction releases heat to the surroundings (exothermic). A positive ΔH means the reaction absorbs heat from the surroundings (endothermic). The magnitude of ΔH tells you how much energy is exchanged per mole of reaction as written.

Enthalpy is a state function, so ΔH depends only on the initial and final states, not on the path taken. This is why Hess’s law works: you can add enthalpy changes of individual steps to get the total ΔH.

Standard enthalpy of formation (ΔHf°) values are tabulated for compounds at 1 bar and a specified temperature (usually 25 °C). To find the enthalpy of a reaction, subtract the sum of formation enthalpies of reactants from that of products:

ΔHrxn° = Σ ΔHf°(products) − Σ ΔHf°(reactants)

Common Mistakes and How to Avoid Them

  • Confusing ΔH with ΔU: They differ by PΔV. For reactions with gas moles changing, the difference can be several kJ. Always check whether your calorimeter is constant-pressure (ΔH) or constant-volume (ΔU).
  • Unit errors: Pressure in atm and volume in L gives PΔV in L·atm. To convert to J, use 1 L·atm = 101.325 J. In this calculator, we use kPa and L to get J directly (1 kPa·L = 1 J).
  • Forgetting to multiply by stoichiometric coefficients: When using formation enthalpies, each coefficient multiplies the corresponding ΔHf°.
  • Sign errors: Heat absorbed by the system is positive (endothermic), heat released is negative (exothermic). In a calorimeter, the heat of the reaction is the negative of the heat gained by the water.
  • Assuming ΔH is independent of temperature: Enthalpy changes with temperature. If you need ΔH at a different temperature, you must use Kirchhoff’s law: ΔH(T₂) = ΔH(T₁) + ∫ΔCp dT.

Limits of the Formula

The definition H = U + PV is exact for any system. The simplification ΔH = qp only holds when the pressure is constant and the only work is P–V work. In a bomb calorimeter, the volume is constant, so the measured heat is ΔU, not ΔH. To convert, you need to know the PΔV term, which often comes from the gas moles change.

For real gases, the ideal gas law is an approximation. At high pressures or low temperatures, the PΔV term deviates from ΔngasRT. For condensed phases (liquids and solids), the volume change is small, so the correction is negligible.

Also, enthalpy is an extensive property—it scales with the amount of substance. When reporting molar enthalpy, divide by the number of moles. The calculator gives total ΔH for the reaction as written; to get per mole, divide by the stoichiometric coefficient of the substance of interest.

Frequently Asked Questions

What is the difference between enthalpy and internal energy?

Internal energy (U) is the total kinetic and potential energy of the particles in a system. Enthalpy (H) is defined as U + PV, which accounts for the energy needed to displace the surroundings to make room for the system. At constant pressure, the heat exchanged equals the enthalpy change, while at constant volume, it equals the internal energy change.

Why is ΔH = qp only at constant pressure?

At constant pressure, the work done by the system is PΔV. The first law says ΔU = q + w, where w = −PΔV. Rearranging gives q = ΔU + PΔV = ΔH. If pressure changes, the heat measured is not simply ΔH because the PΔV term is not just the work done—it also includes changes in pressure that affect the enthalpy.

How do I calculate ΔH from bond energies?

Bond energies are average values for breaking a bond in the gas phase. To estimate ΔH for a reaction, add the bond energies of all bonds broken (positive, since energy is absorbed) and subtract the bond energies of all bonds formed (negative, since energy is released): ΔH ≈ Σ(bonds broken) − Σ(bonds formed). This is an approximation because bond energies are averages over many compounds.

Can enthalpy be negative?

Yes. Enthalpy is a state function, so its absolute value depends on a reference state. For a reaction, ΔH can be negative (exothermic) or positive (endothermic). The standard enthalpy of formation of an element in its most stable form is defined as zero, so compounds can have negative or positive formation enthalpies.

What is the standard enthalpy of formation?

The standard enthalpy of formation (ΔHf°) is the enthalpy change when one mole of a compound is formed from its elements in their standard states at 1 bar and a specified temperature (usually 25 °C). It is used to calculate reaction enthalpies via Hess’s law. For example, ΔHf° of water (liquid) is −285.8 kJ/mol.

How does temperature affect ΔH?

Enthalpy changes with temperature according to the heat capacities of the reactants and products. The relation is Kirchhoff’s law: ΔH(T₂) = ΔH(T₁) + ∫(Cp,products − Cp,reactants) dT. For small temperature differences, you can approximate using average heat capacities. This is why standard enthalpies are reported at a specific temperature, usually 25 °C.

Related

Formula used
in q | Heat absorbed at constant pressure (q_p) | kJ | 12.5 | 0
in u | Change in internal energy (ΔU) | kJ | 10.0 | 0
in p | Pressure | kPa | 101.325 | 0
in dv | Change in volume (ΔV) | L | 2.0 | 0
out dh | Enthalpy change (ΔH) | kJ | q | 2
out dh2 | ΔH from ΔU + PΔV | kJ | u + p * dv / 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →