molecalculator

Moles & Molar Mass

Half Life Definition & Formula

Calculator No. 01-7046 · Updated · Formula and assumptions shown below

Remaining amount 25.0000 g
Fraction remaining
0.2500
= 0.5^(Elapsed time ÷ Half-life)
Initial amount
100 g
Set in the form below
Elapsed time
10 s
Set in the form below
You enter
Initial amount (g), Elapsed time (s), Half-life (s)
You get
Remaining amount (g), Fraction remaining
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Half-life is the time required for half of a given amount of a substance to decay, react, or be eliminated. You enter the starting amount, the decay constant (or half-life itself), and the elapsed time, and the calculator returns the remaining amount. This page explains the concept, the math, and how to use it for radioactive decay, chemical reactions, and drug elimination.

Formula

The basic half-life equation is:

A(t) = A₀ × (1/2)t / t₁/₂

  • A(t) = amount remaining after time t (g, mol, Bq, or any unit)
  • A₀ = initial amount (same unit as A(t))
  • t = elapsed time (s, min, h, d, yr – must match the half-life unit)
  • t₁/₂ = half-life (same time unit as t)

This is an exponential decay model. The exponent t / t₁/₂ tells you how many half-lives have passed. After one half-life, the factor is 0.5; after two, 0.25; after three, 0.125, and so on.

Worked Example

Using the default values from the calculator: initial amount A₀ = 100 g, elapsed time t = 10 s, half-life t₁/₂ = 5 s.

  1. Calculate the number of half-lives: t / t₁/₂ = 10 / 5 = 2.
  2. Apply the decay factor: (1/2)2 = 0.25.
  3. Multiply by the initial amount: 100 × 0.25 = 25 g.

The calculator shows 25 g remaining and a fraction remaining of 0.25. That matches: after 10 seconds (two half-lives of 5 s each), 25% of the original 100 g remains.

Assumptions

  • The decay follows first-order kinetics (the rate is proportional to the amount present).
  • The half-life is constant – it does not change with time, temperature, pressure, or concentration.
  • The substance decays into something else and does not reform.
  • For chemical reactions, this applies only to first-order reactions, not second-order or zero-order.

What Half-Life Really Means

Half-life is a statistical measure. For a large number of atoms, it tells you when half of them have decayed. It does not mean that after two half-lives all atoms are gone – after two, a quarter remain; after three, an eighth; after ten, about 0.1% remains. In practice, a sample is often considered “gone” after about 10 half-lives, but technically it never reaches zero.

The concept applies to any process that decays exponentially:

  • Radioactive decay – e.g., carbon-14 has a half-life of 5,730 years.
  • First-order chemical reactions – e.g., decomposition of hydrogen peroxide in solution.
  • Drug elimination – the time for the body to remove half of a drug dose.
  • Electrical discharge – e.g., voltage decay in a capacitor (though that is often described with a time constant).

How to Use the Calculator

Enter any three of the four values (initial amount, elapsed time, half-life, and the calculator will compute the fourth). The calculator above takes initial amount, elapsed time, and half-life, and returns the remaining amount and fraction. To find half-life from two amounts, you would need to rearrange the formula:

t₁/₂ = t × ln(2) / ln(A₀ / A(t))

For example, if you start with 100 g and after 10 s you have 25 g, then:

t₁/₂ = 10 × ln(2) / ln(100 / 25) = 10 × 0.6931 / ln(4) = 6.931 / 1.386 = 5 s.

This calculator is for study and lab planning. For actual radioactive work, always follow your lab method, the safety data sheet (SDS) and your supervisor.

Common Mistakes

  • Unit mismatch – using seconds for time and hours for half-life. Convert everything to the same unit first.
  • Confusing half-life with mean life – mean life (τ) is the average lifetime of an atom, equal to t₁/₂ / ln(2) ≈ 1.443 × t₁/₂.
  • Assuming half-life applies to second-order reactions – for a second-order reaction, the “half-life” depends on concentration and changes over time.
  • Rounding too early – if you round the number of half-lives to 2 when it is 2.3, you lose accuracy. Keep extra digits until the final step.

Real-World Examples

  • Carbon-14 dating – a living organism has a constant C-14/C-12 ratio. After death, C-14 decays with a half-life of 5,730 years. Measuring the remaining ratio tells you how long ago the organism died.
  • Medical isotopes – technetium-99m has a half-life of about 6 hours, which is short enough to limit patient radiation exposure but long enough for imaging.
  • Nuclear waste – plutonium-239 has a half-life of 24,100 years, meaning it remains hazardous for hundreds of thousands of years.
  • Pharmacokinetics – a drug with a half-life of 4 hours will have about 6.25% of the original dose left after 16 hours (four half-lives).

Limits of the Model

The simple exponential decay model assumes a closed system with no external influences. In reality:

  • Temperature and pressure can affect chemical reaction rates, but not radioactive decay (except in extreme conditions).
  • For drugs, metabolism can be saturable (zero-order at high doses), so the half-life may change with dose.
  • For mixtures of isotopes, you get a composite decay curve that is not a single exponential.
  • For very small samples (a few atoms), the statistical nature becomes significant – you cannot predict exactly when a single atom will decay.

Frequently Asked Questions

What is the difference between half-life and decay constant?

The decay constant (λ) is the probability per unit time that an atom decays. The half-life is related by t₁/₂ = ln(2) / λ. A larger decay constant means a shorter half-life. Both describe the same exponential decay process.

How do I calculate half-life from a graph?

Plot the amount remaining versus time on a semi-log graph (log of amount on the y-axis). The decay will appear as a straight line. The half-life is the time it takes for the line to drop by a factor of 2, or you can read the slope (m) and use t₁/₂ = ln(2) / |m|.

Does half-life change with temperature or pressure?

For radioactive decay, no – it is essentially constant under normal conditions. For chemical reactions, yes, the half-life of a first-order reaction is independent of concentration but does depend on temperature (rate constants increase with temperature). Pressure can also affect reaction rates if the reaction involves gases.

Can half-life be used for second-order reactions?

Strictly, half-life is defined for any reaction, but for a second-order reaction it depends on the initial concentration: t₁/₂ = 1 / (k[A]₀). So it is not a constant for a given reaction – it changes as the reaction proceeds. It is more useful to use the rate constant k for second-order reactions.

What is the half-life of a drug and why does it matter?

Drug half-life is the time for the body to eliminate half of the drug dose. It determines dosing frequency: a drug with a short half-life (e.g., 2 hours) may need to be taken several times a day, while a long half-life (e.g., 24 hours) can be taken once daily. It also affects how long side effects last and how long to wait before changing doses.

Is there a half-life for stable elements?

Stable elements do not decay, so they do not have a half-life. However, some isotopes that are “stable” are actually radioactive with extremely long half-lives (e.g., bismuth-209 has a half-life of about 1.9 × 1019 years). In practice, if the half-life is longer than the age of the universe, we treat it as stable.

Related

Formula used
in a0 | Initial amount | g | 100 | 0
in t | Elapsed time | s | 10 | 0
in h | Half-life | s | 5 | 0.000001
out a | Remaining amount | g | a0 * 0.5^(t / h) | 4
out frac | Fraction remaining | - | 0.5^(t / h) | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →