Enthalpy (H) is the total heat content of a system at constant pressure, and its change (ΔH) is calculated as the heat absorbed or released during a process. You calculate ΔH using the formula ΔH = ΔU + PΔV for a physical change, or more practically, ΔH = m·c·ΔT for a temperature change in a substance, or by summing bond energies or heats of formation for chemical reactions. This article explains each method, the units, and how to apply them correctly.
Formula
The most common calorimetry equation is:
ΔH = m × c × ΔT
- ΔH – enthalpy change (joules, J; or kilojoules, kJ)
- m – mass of the substance (grams, g)
- c – specific heat capacity (J/(g·K) or J/(g·°C))
- ΔT – temperature change, Tfinal − Tinitial (K or °C; the size of a kelvin equals a degree Celsius, so the difference is the same in either unit)
For a chemical reaction at constant pressure, enthalpy change can also be found from standard enthalpies of formation:
ΔH°rxn = Σ ΔH°f(products) − Σ ΔH°f(reactants)
where ΔH°f is the standard enthalpy of formation of each compound (kJ/mol), and each term is multiplied by its stoichiometric coefficient.
Worked Example
Using the calculator defaults: heat 100.0 g of water (c = 4.184 J/(g·K)) from 25.0 °C to 35.0 °C.
- Calculate ΔT: 35.0 − 25.0 = 10.0 °C (which equals 10.0 K)
- Multiply: ΔH = 100.0 g × 4.184 J/(g·K) × 10.0 K = 4184 J
- Convert to kJ: 4184 J ÷ 1000 = 4.184 kJ
The calculator returns ΔH = 4184.0 J (4.184 kJ). A positive value means heat is absorbed (endothermic).
Assumptions
- The specific heat capacity is constant over the temperature range.
- No heat is lost to the surroundings (perfect insulation).
- The process occurs at constant pressure.
- The substance does not change phase (no melting or boiling) during the temperature change.
When to Use Each Enthalpy Calculation
Choose the method based on what you know and what you need:
- Temperature change of a substance – use ΔH = m·c·ΔT. This works for heating or cooling a single phase (solid, liquid, or gas).
- Phase change – use ΔH = n × ΔHfus or ΔH = n × ΔHvap, where n is moles and ΔHfus/ΔHvap are the molar heats of fusion/vaporization (kJ/mol). Temperature stays constant during a phase change.
- Chemical reaction – use standard enthalpies of formation (Hess’s law) or bond dissociation energies. The formation method is more accurate and commonly tabulated.
- From internal energy – for reactions where gases are involved, ΔH = ΔU + ΔngasRT, where Δngas is the change in moles of gas, R = 8.314 J/(mol·K), and T is the absolute temperature (K).
Common Mistakes and How to Avoid Them
- Mixing up mass and moles – the calorimetry formula uses mass (g), not moles. If you have moles, convert using molar mass first.
- Using the wrong specific heat – water is 4.184 J/(g·K), but ice is about 2.09, steam about 2.01, and metals are much lower (e.g., iron ≈ 0.45). Always check the substance.
- Ignoring the sign of ΔT – if the final temperature is lower than the initial, ΔT is negative, giving a negative ΔH (exothermic). Many students drop the sign and report the wrong direction.
- Forgetting to multiply by stoichiometric coefficients – in the formation method, each ΔH°f must be multiplied by its coefficient in the balanced equation.
- Rounding too early – keep at least 3–4 significant figures in intermediate steps to avoid large final errors.
Units and Conversions
Enthalpy is commonly reported in joules (J) or kilojoules (kJ). For molar quantities, use kJ/mol. When working with gas constants, remember:
- 1 kJ = 1000 J
- 1 cal = 4.184 J
- R = 8.314 J/(mol·K) = 0.0820574 L·atm/(mol·K)
If you measure pressure in atm and volume in liters, convert to joules using 1 L·atm = 101.325 J. Always convert to SI units before plugging into formulas that include R.
Limits of the Calorimetry Formula
The equation ΔH = m·c·ΔT assumes constant pressure and no phase change. It also assumes the specific heat is constant, but real specific heats vary slightly with temperature. For large temperature swings, you would need to integrate c(T) over the range. Additionally, in a coffee-cup calorimeter, heat absorbed by the container itself is usually neglected; for precise work, you must account for the calorimeter’s heat capacity (calibration factor).
For chemical reactions, the formation method assumes standard conditions (25 °C, 1 atm) and that reactants and products are in their standard states. If your reaction is not at 25 °C, you must use Kirchhoff’s law to adjust for temperature differences.
Frequently Asked Questions
What is the difference between enthalpy and internal energy?
Internal energy (U) is the total kinetic and potential energy of molecules. Enthalpy (H = U + PV) adds the work done to make room for the system at constant pressure. For reactions with no gas volume change, ΔH ≈ ΔU. When gases are produced or consumed, the difference is ΔngasRT, which can be significant.
Why is enthalpy change positive for melting but negative for freezing?
Melting requires energy to break intermolecular bonds, so the system absorbs heat (ΔH > 0). Freezing releases that same energy (ΔH < 0). The magnitude is equal but opposite in sign.
Can I calculate enthalpy from bond energies?
Yes, approximate ΔHrxn = Σ(bond energies broken) − Σ(bond energies formed). This method is rough because bond energies are averages from many molecules. It works well for simple gas-phase reactions but less well for solids or liquids.
Does temperature affect ΔH?
Yes, ΔH changes with temperature because specific heats of reactants and products differ. The correction is given by Kirchhoff’s law: ΔH(T2) = ΔH(T1) + ∫ΔCp dT. For small temperature differences, the change is often small and ignored.
What does a negative ΔH mean in a chemical reaction?
A negative ΔH means the reaction releases heat to the surroundings (exothermic). The products have lower enthalpy than the reactants. Combustion, neutralization, and most oxidation reactions are exothermic.
How do I find the specific heat capacity of a substance?
Look it up in a standard reference table or measure it experimentally using a calorimeter. For water, it is 4.184 J/(g·K). For other common substances, values are widely tabulated in textbooks and online databases.
Related
Formula used
in m | Mass of substance | g | 100.0 | 0 in c | Specific heat capacity | J/(g·K) | 4.184 | 0 in t1 | Initial temperature | °C | 25.0 | -273.15 in t2 | Final temperature | °C | 35.0 | -273.15 out dh | Enthalpy change (ΔH) | J | m * c * (t2 - t1) | 1 out dhkj | Enthalpy change (ΔH) | kJ | dh / 1000 | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- How to Find the Continuous Decay Rate
- Total Constant of Decay: How to Calculate It0.000121 1/s
- How to Calculate Decay Constant0.000121 1/s
- Half Life GitHub: What It Is and How to Use It
- Decay Constant: How to Calculate It0.000121 1/s
- Half-Life Games in Order: Full Release Timeline