molecalculator

Moles & Molar Mass

Ksp to Concentration: Solubility Calculator

Calculator No. 01-6829 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Convert a solubility product, Ksp, into the molar concentration of ions by using the salt’s dissolution equation and its stoichiometric coefficients. Enter Ksp and the formula-unit solubility; the calculator returns the molar solubility and the equilibrium concentrations for a salt that dissolves completely into the listed ions.

Formula

For silver chloride, the dissolution reaction is AgCl(s) ⇌ Ag+(aq) + Cl−(aq). Its solubility-product expression is Ksp = [Ag+][Cl−]. If the molar solubility is s mol/L and there is no other source of either ion, [Ag+] = s and [Cl−] = s. Therefore Ksp = s² and s = √Ksp. Concentrations of both ions equal s.

In the calculator, k is the dimensionless numerical Ksp value for AgCl under the chosen convention, and s is the molar solubility in mol/L. The calculator uses s as the concentration input so that it can show the direct stoichiometric conversion and verify Ksp; for the example, s is the equilibrium solubility implied by √k. The first output is s, followed by the ion concentrations and their product. Ksp is formally expressed using activities, which are approximated by concentrations in the dilute-solution treatment used here.

Worked Example

For the example, use Ksp = 1.08 × 10−10 and calculate s:

  • Ksp = s²
  • s = √(1.08 × 10−10) = 1.0392 × 10−5 mol/L
  • [Ag+] = s = 1.0392 × 10−5 mol/L
  • [Cl−] = s = 1.0392 × 10−5 mol/L
  • [Ag+][Cl−] = (1.0392 × 10−5)(1.0392 × 10−5) ≈ 1.0800 × 10−10

The block’s default solubility entry is 0.0004762 mol/L, a convenient round value for demonstrating the concentration-to-Ksp check; it is not the solubility implied by the default Ksp. For a Ksp-to-concentration calculation, replace that entry with the calculated solubility, 1.0392 × 10−5 mol/L. The calculator’s first output always reports the value entered as s, so the Ksp-derived result is obtained from the formula above.

Assumptions

  • The salt is AgCl and dissolves according to a 1:1:1 stoichiometric ratio.
  • No Ag+ or Cl− is present from another source; there is no common-ion effect.
  • The solution is dilute enough that activities are approximated by concentrations.
  • The solid phase is present at equilibrium, and temperature is held constant at the temperature associated with the supplied Ksp.

For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

How Ksp Converts to Concentration

Ksp is not generally the concentration of a dissolved salt. It is the equilibrium product of the dissolved-ion activities, each raised to a power given by the balanced dissolution equation. To get concentrations, first identify the ions and coefficients, then express each ion concentration in terms of the molar solubility s. Substituting those expressions into the Ksp equation gives an equation to solve for s.

For a general salt AmBn dissolving as AmBn(s) ⇌ mA + nB, the ideal concentration expression is Ksp = [A]m[B]n. If one formula unit produces m A ions and n B ions, then [A] = ms and [B] = ns, giving Ksp = (ms)m(ns)n. The exponent matters: simply taking the square root works only when the resulting equation is Ksp = s².

Examples for Different Salt Ratios

For calcium fluoride, CaF2(s) ⇌ Ca2+ + 2F−. In pure water, [Ca2+] = s and [F−] = 2s, so Ksp = s(2s)² = 4s³. Thus s = (Ksp/4)1/3, not √Ksp. Once s is found, the equilibrium fluoride concentration is 2s.

For aluminum hydroxide, Al(OH)3(s) ⇌ Al3+ + 3OH−, the ideal expression is Ksp = s(3s)³ = 27s⁴ in pure water, before considering water autoionization or other equilibrium effects. The fourth root is required to solve for s. These examples show why the balanced equation must come before arithmetic.

Common-Ion Effects and Limits

If the solution already contains one of the ions, its equilibrium concentration is not just the amount contributed by dissolution. For AgCl in a solution initially containing chloride concentration C, the ideal expression is Ksp = s(C + s), assuming no initial silver ion and no other reactions. When C is much greater than s, s is approximately Ksp/C. The square-root shortcut no longer applies.

Likewise, complex formation, acid-base reactions, hydrolysis, competing solids, and non-ideal ionic strength can change the relationship between total dissolved material and free-ion concentrations. At appreciable concentrations, activities rather than raw molar concentrations are needed. A tabulated Ksp may also be reported for a particular temperature; do not assume values from different temperatures are interchangeable.

Using the Result Correctly

  • Write and balance the dissolution reaction, including ion coefficients.
  • Write the Ksp expression from the dissolved ions, omitting the pure solid.
  • Set each ion concentration equal to its stoichiometric coefficient times s, adding any initial ion concentration where relevant.
  • Solve for s, then calculate each ion concentration and check that their product reproduces Ksp.

Keep units consistent: s and ion concentrations are normally in mol/L. Ksp is commonly presented as a numerical value with no units under the activity convention, although concentration-based expressions can appear to carry powers of concentration. Avoid rounding s too early, since the ion concentrations are then multiplied or raised to powers. The concentration of a dissolved formula unit is also not always the concentration of any one ion; stoichiometric coefficients determine the difference.

Frequently Asked Questions

Is Ksp the same as molar solubility?
No. Ksp is an equilibrium constant for dissolved ions, while molar solubility s is the amount of solid formula units dissolved per liter. Their relationship depends on the dissolution stoichiometry.

Can I find concentration by taking the square root of Ksp?
Only for a 1:1 salt such as AgCl in pure water under the ideal approximation, where Ksp = s². Other stoichiometric ratios produce different powers and coefficients.

Does a common ion change Ksp?
At a fixed temperature, adding a common ion does not change the thermodynamic Ksp. It changes the equilibrium concentrations and usually reduces the salt’s molar solubility.

Why does my calculated concentration differ from a reference value?
Check the temperature, balanced dissolution equation, ion coefficients, and whether the reference assumes pure water, ignores activity effects, or includes a common ion or complex formation.

Can Ksp alone give every ion concentration?
Not always. For a simple salt dissolving in pure water, stoichiometry may be enough. Initial ions and side reactions add unknowns that require additional equilibrium information.

Related

Formula used
in k | Ksp | - | 1.08e-10 | 0
in s | Molar solubility | mol/L | 0.0004762 | 0
out x | Molar solubility | mol/L | s | 6
out a | Ag+ concentration | mol/L | s | 6
out b | Cl- concentration | mol/L | s | 6
out check | Ksp from concentrations | - | a * b | 10

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →