This calculator converts a volume of natural gas in standard cubic feet (scf) to its mass in pounds (lb) using the gas’s molecular weight and the ideal gas law at standard conditions. You enter the gas volume in scf and the molecular weight of the gas (methane is the default), and you get the mass in pounds and kilograms. The calculation is based on the fact that one pound-mole of any ideal gas occupies 379.3 scf at 60°F and 14.696 psia.
Formula
The conversion uses the ideal gas law to relate volume to moles, then converts moles to mass. At standard conditions (60°F, 14.696 psia), one pound-mole of an ideal gas occupies 379.3 standard cubic feet. The formula is:
m (lb) = V (scf) × MW (g/mol) / 379.3 (scf/lb-mol)
- V = volume of gas in standard cubic feet (scf)
- MW = molecular weight of the gas in grams per mole (g/mol) – for methane, 16.043 g/mol
- 379.3 = volume occupied by one pound-mole of any ideal gas at 60°F and 14.696 psia (in scf/lb-mol)
The result is the mass in pounds (lb). To get kilograms, multiply by 0.45359237 (exact conversion factor).
Worked Example
Using the default values: V = 1000 scf, MW = 16.043 g/mol (methane).
- Calculate pound-moles: 1000 scf ÷ 379.3 scf/lb-mol = 2.6364 lb-mol
- Convert to mass in lb: 2.6364 lb-mol × 16.043 lb/lb-mol = 42.30 lb
- Convert to kg: 42.30 lb × 0.45359237 kg/lb = 19.19 kg
The calculator shows 42.300 lb for the first output, matching the manual calculation.
Assumptions
- Ideal gas behavior (valid for natural gas at typical pipeline conditions).
- Standard conditions: 60°F (15.6°C) and 14.696 psia (1 atm).
- Gas composition is pure methane – real natural gas contains ethane, propane, and other components, so the molecular weight should be adjusted for the actual composition.
- The volume is measured at the same standard conditions – if your volume is at different conditions, you must correct it first.
Why Convert scf to lb?
Natural gas is bought, sold, and transported by volume (scf) in many contexts, but engineering calculations, combustion analysis, and mass balance often require mass. For example, when determining the amount of CO2 produced by burning a given volume of gas, you need the mass of methane. Similarly, pipeline capacity and compressor sizing depend on mass flow, not just volume. Converting scf to lb lets you compare gas quantities on a mass basis, which is independent of temperature and pressure (as long as you use the same standard conditions).
How to Choose the Right Molecular Weight
Natural gas is not pure methane. Typical pipeline gas in the U.S. is about 90–95% methane, with ethane (C2H6, 30.07 g/mol), propane (C3H8, 44.10 g/mol), nitrogen (28.01 g/mol), and carbon dioxide (44.01 g/mol) making up the rest. The average molecular weight of a gas mixture is the mole-fraction-weighted average of its components. For example, a gas with 92% methane, 5% ethane, 2% nitrogen, and 1% CO2 has an average MW of:
MW = 0.92×16.043 + 0.05×30.07 + 0.02×28.01 + 0.01×44.01 = 17.30 g/mol
If you only know the specific gravity (SG) of the gas relative to air (SG = MW / 28.96), you can compute MW = SG × 28.96. For most rough estimates, using 16.043 (pure methane) is acceptable, but for accurate billing or engineering, use the actual gas analysis.
Common Mistakes and Misconceptions
- Using the wrong standard conditions: There are several “standard” definitions. The U.S. oil and gas industry commonly uses 60°F and 14.696 psia (1 atm) for scf. Some use 15°C (59°F) or 0°C (32°F) – the latter gives a different molar volume. Always confirm which standard your volume refers to.
- Confusing scf with actual cubic feet (acf): scf is corrected to standard conditions; acf is the actual volume at the operating temperature and pressure. You cannot convert acf to lb without first correcting to standard conditions using the gas law.
- Forgetting the molecular weight is in g/mol but the result is in lb: The formula works because one pound-mole has a mass equal to the molecular weight in pounds. If you use g/mol, the numeric value is the same for lb/lb-mol.
- Rounding too early: The constant 379.3 is rounded from 379.485 (the exact value for 60°F, 14.696 psia). For high-precision work, use 379.485.
Related Conversions and Comparisons
If you need to convert mass to volume, simply rearrange the formula: V (scf) = m (lb) × 379.3 / MW. This is useful when you know the mass of gas in a cylinder and want to know how many scf it represents. Another common conversion is from scf to MMBtu (million British thermal units). The heating value of natural gas is about 1,030 Btu per scf (for pipeline gas), so 1,000 scf ≈ 1.03 MMBtu. However, this varies with composition – methane has a higher heating value of 1,010 Btu/scf, while ethane adds about 1,780 Btu/scf. If you have a gas analysis, you can calculate the exact heating value.
For comparison, one pound of methane contains about 23,800 Btu of energy (higher heating value). So 1,000 scf of methane (42.3 lb) contains about 1,007,000 Btu, or roughly 1.0 MMBtu – consistent with the rule of thumb.
Costs and Billing
Natural gas is often billed in therms (100,000 Btu) or MMBtu, not by mass. However, some industrial contracts bill by mass (e.g., per pound) when the gas is sold as a liquid or compressed. To estimate cost, you need the price per MMBtu and the heating value. For example, if gas costs $4.00 per MMBtu, then 1,000 scf (≈1.03 MMBtu) costs about $4.12. The mass conversion helps you compare prices across different units. Always check your utility bill to see which unit they use – residential bills typically use therms, while commercial may use MMBtu or scf.
Safety and Practical Notes
Natural gas is flammable and can form explosive mixtures with air (approximately 5–15% by volume). When handling gas samples or performing conversions for safety calculations, always ensure proper ventilation and follow your facility’s safety protocols. For engineering work, refer to the safety data sheet (SDS) for the specific gas mixture. The conversion itself is purely mathematical and safe to perform, but any actual gas handling requires trained personnel and appropriate equipment. Also, remember that gas volume changes with temperature and pressure – a “standard” cubic foot is a fixed quantity of gas, but the physical volume it occupies in a pipeline depends on operating conditions.
Frequently Asked Questions
How many pounds is 100 scf of natural gas?
Using pure methane (MW=16.043), 100 scf ÷ 379.3 scf/lb-mol = 0.2636 lb-mol × 16.043 lb/lb-mol = 4.23 lb. For typical pipeline gas with MW≈17.3, it would be about 4.56 lb.
What is the difference between scf and SCFM?
scf is a volume (cubic feet at standard conditions). SCFM is a flow rate – standard cubic feet per minute. To get mass flow, multiply SCFM by the density at standard conditions (e.g., 0.0423 lb/scf for methane) to get lb/min.
Does the conversion change if I use metric standard conditions?
Yes. If you use 0°C and 1 atm, one mole occupies 22.414 L, which corresponds to a different scf equivalent. The U.S. industry uses 60°F, but many international standards use 15°C or 0°C. Always match the standard conditions of your volume measurement.
Can I use this calculator for other gases?
Yes, as long as you enter the correct molecular weight. The ideal gas law applies to any gas at standard conditions. For example, propane (MW=44.10) would give 1000 scf = 116.3 lb.
Why is the constant 379.3 and not 379.5?
379.3 is a rounded value. The exact volume of one pound-mole at 60°F and 14.696 psia is 379.485 scf. For most purposes, 379.3 is accurate to 0.05%, which is fine. If you need more precision, use 379.485.
How do I convert lb back to scf?
Use the inverse: scf = lb × 379.3 / MW. For example, 42.3 lb of methane ÷ 16.043 × 379.3 = 1000 scf.
Related
Formula used
in v | Gas volume | scf | 1000 | 0 in mw | Molecular weight | g/mol | 16.043 | 1 out lbm | Mass | lb | v * mw / 379.3 | 3 out kg | Mass in kilograms | kg | lbm * 0.45359237 | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Relative Molecular Mass of Copper Sulfate0.0732 mol/L
- Bag Volume Calculator: How to Measure Any Bag25.50 L
- Molar Mass of Copper(II) Sulfate (CuSO₄)0.0468 mol/L
- Molar Mass of Hydrated Copper Sulphate (CuSO4·5H2O)0.0468 mol/L
- Molar Mass of Copper(II) Sulfate: Exact Value & How to Find It0.0732 mol/L
- Molar Mass of CuSO4: How to Calculate It0.1000 mol