A basic (alkaline) solution has a pH greater than 7.0 at 25 °C. The pH scale runs from 0 to 14, where 7 is neutral, below 7 is acidic, and above 7 is basic. The higher the pH, the more basic (alkaline) the solution is.
Formula
For a strong base that fully dissociates (like NaOH or KOH), the pH is calculated from the hydroxide ion concentration [OH⁻]:
pOH = -log₁₀[OH⁻]
pH = 14 – pOH (at 25 °C)
Where:
- [OH⁻] = molar concentration of hydroxide ions (mol/L)
- pOH = negative logarithm of the hydroxide ion concentration
- pH = negative logarithm of the hydrogen ion concentration
- 14 = pKw at 25 °C (the self-ionization constant of water)
For a strong monoprotic base like NaOH, [OH⁻] equals the molarity of the base. For a strong diprotic base like Ba(OH)₂, [OH⁻] = 2 × molarity.
Worked Example
Using the calculator defaults: dissolve 2.922 g of NaCl (molar mass 58.44 g/mol) in water to a final volume of 250 mL. This is a neutral salt, not a base, but the molarity calculation is identical for any solute.
Step 1: Convert mass to moles.
Moles = 2.922 g ÷ 58.44 g/mol = 0.05000 mol
Step 2: Convert volume to liters.
250 mL ÷ 1000 = 0.250 L
Step 3: Calculate molarity.
Molarity = 0.05000 mol ÷ 0.250 L = 0.2000 mol/L
So the concentration is 0.2000 M (200.0 mM). If this were a strong base like NaOH at 0.2000 M, then [OH⁻] = 0.2000 M, pOH = -log₁₀(0.2000) = 0.6990, and pH = 14 – 0.6990 = 13.30.
Assumptions
- Temperature is 25 °C (pH scale changes with temperature).
- The base is strong and dissociates completely.
- The solution is dilute enough that activity coefficients are close to 1.
- Final volume is used, not solvent volume.
Understanding the pH Scale
The pH scale is logarithmic, meaning each whole number change represents a tenfold change in hydrogen ion concentration. A solution with pH 11 has ten times fewer hydrogen ions than one with pH 10, and a hundred times fewer than pH 9.
Common basic solutions include:
- Baking soda solution (pH ~8.3)
- Household ammonia (pH ~11)
- Limewater (calcium hydroxide, pH ~12.4)
- Drain cleaner (sodium hydroxide, pH ~13-14)
Pure water at 25 °C has a pH of exactly 7.0. As temperature increases, the neutral pH shifts lower (e.g., 6.92 at 37 °C) because the self-ionization of water is endothermic.
How to Measure pH
Three common methods are used to measure pH:
- pH meter: Most accurate, uses a glass electrode. Requires calibration with buffer solutions (pH 4, 7, 10) and temperature compensation.
- pH paper (litmus): Quick and cheap, but only gives a range (e.g., pH 10-12).
- Indicator solutions: Like phenolphthalein (colorless below 8.2, pink above 10) or universal indicator (color changes across the scale).
For laboratory work, a calibrated pH meter is the standard. Always measure at the same temperature as your experiment, because pH changes with temperature.
Common Mistakes and Misconceptions
Mistake 1: Assuming pH 14 is the maximum for all bases. Concentrated strong bases can have pH above 14 in terms of hydrogen ion activity, but the simple pH scale is usually reported as 0-14. A 10 M NaOH solution has a calculated pH of 15, but the actual measured pH is lower due to activity effects.
Mistake 2: Forgetting the factor of 2 for diprotic bases. For Ba(OH)₂, each mole gives 2 moles of OH⁻. A 0.01 M Ba(OH)₂ solution has [OH⁻] = 0.02 M, giving pOH = 1.70 and pH = 12.30, not 12.00.
Mistake 3: Using volume of solvent instead of final volume. When you dissolve a solid in water, the final volume is usually larger than the solvent volume. Always use the final solution volume.
Mistake 4: Confusing strong and weak bases. A weak base like ammonia (NH₃) does not fully dissociate. Its pH must be calculated using the base dissociation constant (Kb). For 0.1 M ammonia (Kb = 1.8×10⁻⁵), [OH⁻] ≈ 1.34×10⁻³ M, so pOH = 2.87 and pH = 11.13, not 13.
Choosing the Right Base for a Target pH
To prepare a basic solution of a specific pH, you need to know:
- Whether the base is strong or weak
- For strong bases: the molarity needed is simply 10^(-(14-pH)) for monoprotic bases
- For weak bases: you need the Kb value and use the equilibrium expression
Example: To make 500 mL of a pH 12.00 solution with NaOH (strong, monoprotic):
[OH⁻] = 10^(-2.00) = 0.0100 M
Moles needed = 0.0100 mol/L × 0.500 L = 0.00500 mol
Mass needed = 0.00500 mol × 40.00 g/mol = 0.200 g NaOH
For weak bases, the calculation is more involved. For a solution of a weak base with concentration C and Kb, [OH⁻] ≈ sqrt(Kb × C) if the base is less than 5% dissociated. Then pH = 14 – pOH.
Safety and Handling of Basic Solutions
Concentrated basic solutions are corrosive and can cause severe burns. Always:
- Wear safety goggles and gloves
- Add base to water, not water to base (to prevent splattering)
- Work in a well-ventilated area
- Neutralize spills with a weak acid (like vinegar) before cleanup
- Follow your lab method, the safety data sheet (SDS) and your supervisor
Never mix bleach (sodium hypochlorite) with ammonia or acids, as toxic gases can form. Always store basic solutions in clearly labeled containers.
Frequently Asked Questions
What is the pH of a 0.1 M NaOH solution?
NaOH is a strong base that dissociates completely. [OH⁻] = 0.1 M, so pOH = 1.0, and pH = 14 – 1 = 13.0.
Can pH be above 14?
In theory, yes, for extremely concentrated strong bases. A 1 M NaOH solution has pH 14, but a 10 M solution has a calculated pH of 15. However, the pH scale is usually reported as 0-14, and measurements become unreliable at extreme concentrations due to activity effects.
Why does pH change with temperature?
The self-ionization of water (Kw) increases with temperature. At 25 °C, Kw = 1.0×10⁻¹⁴, so neutral pH = 7. At 50 °C, Kw ≈ 5.5×10⁻¹⁴, making neutral pH ≈ 6.63. A solution that is neutral at 25 °C will have a lower pH at higher temperatures, even though it is still neutral.
Is a higher pH always more dangerous?
Not necessarily. A pH 14 solution is extremely corrosive, but a pH 8 solution is relatively mild. The danger depends on concentration and the specific chemical. For example, a dilute solution of a strong base can be less dangerous than a concentrated solution of a weak base.
How do I calculate pH of a weak base?
Use the base dissociation constant (Kb). For a weak base B, the equilibrium is B + H₂O ⇌ BH⁺ + OH⁻. Set up an ICE table, solve for [OH⁻] using Kb = [BH⁺][OH⁻]/[B], then calculate pOH and pH. For many weak bases, the approximation [OH⁻] ≈ sqrt(Kb × C) works if the base is less than 5% dissociated.
What is the difference between a base and an alkali?
An alkali is a base that dissolves in water to produce hydroxide ions. All alkalis are bases, but not all bases are alkalis. For example, ammonia (NH₃) is a base because it accepts protons, but it is not an alkali because it does not contain OH⁻ ions; it produces them when reacting with water.
Related
Formula used
in m | Mass of solute | g | 2.922 | 0 in mm | Molar mass | g/mol | 58.44 | 0.001 in v | Final solution volume | mL | 250 | 0.001 out c | Molarity | mol/L | m / mm / (v / 1000) | 4 out cmm | Concentration in millimolar | mM | c * 1000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- How to Find the Continuous Decay Rate
- Total Constant of Decay: How to Calculate It0.000121 1/s
- How to Calculate Decay Constant0.000121 1/s
- Half Life GitHub: What It Is and How to Use It
- Decay Constant: How to Calculate It0.000121 1/s
- Half-Life Games in Order: Full Release Timeline