molecalculator

Moles & Molar Mass

Salt Hydrolysis pH Formula & How to Use It

Calculator No. 01-6951 · Updated · Formula and assumptions shown below

Salt concentration 0.1999 mol/L
pH of solution
9.03
Result, rounded to 2 decimal places
Mass of salt
4.1 g
Set in the form below
Molar mass of salt
82.03 g/mol
Set in the form below
You enter
Mass of salt (g), Molar mass of salt (g/mol), Final solution volume (mL), Acid pKa (conjugate acid)
You get
Salt concentration (mol/L), pH of solution
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Salt hydrolysis pH depends on whether the salt comes from a strong or weak acid and base. The formula for the pH of a salt of a weak acid and strong base is pH = 7 + ½(pKa + log C), and for a salt of a strong acid and weak base it is pH = 7 − ½(pKb + log C), where C is the salt concentration in mol/L. This article explains how to derive these formulas, when each applies, and how to handle salts of two weak components.

Formula

The pH of a salt solution is calculated from the hydrolysis (reaction with water) of the ion that acts as a weak acid or weak base. For a salt of a weak acid and a strong base (e.g., sodium acetate, CH₃COONa), the acetate ion hydrolyzes:

CH₃COO⁻ + H₂O ⇌ CH₃COOH + OH⁻

The hydroxide produced makes the solution basic. The pH is given by:

pH = 7 + ½(pKa + log C)

where pKa is the acid dissociation constant of the conjugate acid (acetic acid, pKa = 4.75) and C is the salt concentration in mol/L.

For a salt of a strong acid and a weak base (e.g., ammonium chloride, NH₄Cl), the ammonium ion hydrolyzes:

NH₄⁺ + H₂O ⇌ NH₃ + H₃O⁺

The hydronium produced makes the solution acidic. The pH is:

pH = 7 − ½(pKb + log C)

where pKb is the base dissociation constant of the weak base (ammonia, pKb = 4.75).

For a salt of a weak acid and a weak base (e.g., ammonium acetate), the pH is independent of concentration:

pH = 7 + ½(pKa − pKb)

All formulas assume the salt fully dissociates in water and that hydrolysis is the only significant reaction.

Worked Example

Using the calculator defaults: 4.10 g of sodium acetate (CH₃COONa, molar mass 82.03 g/mol) dissolved in 250 mL of water, with pKa = 4.75 for acetic acid.

Step 1 – Calculate the salt concentration in mol/L:

C = mass / molar mass / volume in L = 4.10 g / 82.03 g/mol / 0.250 L = 0.1999 mol/L (≈ 0.200 M)

Step 2 – Apply the formula for a weak acid salt:

pH = 7 + ½(pKa + log C) = 7 + ½(4.75 + log 0.200)

log 0.200 = −0.6990

pH = 7 + ½(4.75 − 0.6990) = 7 + ½(4.051) = 7 + 2.026 = 9.03

The calculator gives pH = 9.03 (rounded to two decimals), matching the step-by-step result. The solution is basic, as expected for sodium acetate.

Assumptions

  • The salt dissociates completely in water.
  • The solution is dilute (activity coefficients ≈ 1).
  • Temperature is 25 °C; pKa and pKb values are temperature-dependent.
  • Only hydrolysis of the salt ion is considered; water autoionization is negligible except at very low concentrations (below ~10⁻⁶ M).
  • The salt is a simple salt, not a buffer mixture.

How to Choose the Right Formula

Identify the parent acid and base of the salt. The four combinations are:

  • Weak acid + strong base (e.g., sodium acetate, sodium carbonate, potassium cyanide): use pH = 7 + ½(pKa + log C). The anion is the conjugate base of a weak acid.
  • Strong acid + weak base (e.g., ammonium chloride, pyridinium chloride): use pH = 7 − ½(pKb + log C). The cation is the conjugate acid of a weak base.
  • Weak acid + weak base (e.g., ammonium acetate, ammonium formate): use pH = 7 + ½(pKa − pKb). Concentration cancels out.
  • Strong acid + strong base (e.g., NaCl, KBr): no hydrolysis, pH = 7.00 at 25 °C.

For a salt with a cation that is a weak acid and an anion that is a weak base, the pH depends on which is stronger. If pKa of the cation’s conjugate acid is less than pKb of the anion’s conjugate base, the solution is acidic; if greater, it is basic.

Common Mistakes and Misconceptions

A frequent error is using the pKa of the weak acid directly for a salt of a strong acid and weak base. For ammonium chloride, the relevant value is the pKb of ammonia (4.75), not the pKa of ammonium (9.25). The two are related by pKa + pKb = 14 at 25 °C, so either can be used if converted correctly.

Another mistake is forgetting to convert volume to liters. The concentration in the formula must be in mol/L, so a 250 mL volume becomes 0.250 L. Mixing milliliters into the log term gives a pH off by about 1.5 units.

A common misconception is that all salts of weak acids are strongly basic. The pH depends on concentration: a 0.001 M sodium acetate solution has pH ≈ 7.88, while a 1.0 M solution has pH ≈ 9.38. The formula accounts for this through the log C term.

Rounding too early also causes errors. Keep at least three significant figures in the log term before the final rounding. For example, log(0.200) = −0.6990, not −0.7, which would shift the pH by 0.01–0.02 units.

When the Formula Breaks Down

The simple hydrolysis formulas fail in several real situations:

  • Very dilute solutions (below ~10⁻⁶ M): water autoionization contributes significant H⁺ and OH⁻, so the pH approaches 7 but never exactly reaches it without considering Kw.
  • Polyprotic acids: salts like sodium carbonate (Na₂CO₃) hydrolyze in two steps. The first hydrolysis dominates, but the second step (HCO₃⁻ → H₂CO₃) shifts the pH slightly. The simple formula gives an approximation, not an exact value.
  • High ionic strength: activity coefficients drop below 1, so the effective concentration is lower than the measured molarity. In seawater or concentrated buffer systems, measured pH differs from the calculated value by 0.1–0.3 units.
  • Temperature changes: pKa and pKb change with temperature. For example, the pKa of water (Kw) shifts from 14.00 at 25 °C to about 13.26 at 60 °C, changing the pH of neutral water to 6.63.

For precise work, always verify with a calibrated pH meter. The meter reading is the real check because it accounts for temperature, ionic strength, and any dissolved CO₂ from the air that can lower pH.

Practical Applications

Salt hydrolysis pH calculations are used in:

  • Buffer preparation: knowing the pH of a salt solution helps design buffer systems. A buffer of acetic acid and sodium acetate has a pH near 4.75, but the salt alone gives a basic solution around pH 9.
  • Biochemistry: ammonium salts are common in protein precipitation; their pH affects protein stability and solubility.
  • Water treatment: sodium carbonate (soda ash) raises pH to precipitate hardness ions; the hydrolysis formula predicts the dose needed.
  • Food chemistry: sodium bicarbonate (baking soda) in water gives pH ≈ 8.3 at typical concentrations, which affects browning and leavening reactions.
  • Analytical chemistry: choosing a salt for a titration endpoint often requires predicting whether the solution will be acidic or basic at the equivalence point.

In the lab, always follow your method and the safety data sheet (SDS) for the salt you handle. Many salts are irritants or have specific disposal requirements.

Frequently Asked Questions

What is the pH of a 0.1 M sodium acetate solution?
Using pKa = 4.75: pH = 7 + ½(4.75 + log 0.1) = 7 + ½(4.75 − 1) = 7 + 1.875 = 8.88. The solution is basic because acetate is a weak base.

Why is ammonium chloride solution acidic?
Ammonium chloride comes from ammonia (weak base) and hydrochloric acid (strong acid). The NH₄⁺ ion donates a proton to water, forming NH₃ and H₃O⁺, lowering the pH. At 0.1 M, pH ≈ 5.13.

Does salt concentration affect the pH of a weak acid salt?
Yes. The log C term in the formula means higher concentrations give higher pH for weak-acid salts. Doubling the concentration increases pH by about 0.15 units. For weak-acid/weak-base salts, concentration has no effect on pH.

How do I find pKa or pKb values?
Reference tables in textbooks or online databases list pKa for common acids and pKb for common bases. For a conjugate pair, pKa + pKb = 14 at 25 °C. If you know one, you can calculate the other.

What is the pH of sodium chloride solution?
Sodium chloride comes from a strong acid (HCl) and strong base (NaOH), so neither ion hydrolyzes. The pH is 7.00 at 25 °C, assuming pure water and no dissolved CO₂. In practice, exposure to air can lower it to about 5.5–6.5.

Can I use these formulas for buffer solutions?
No. Buffer solutions contain both a weak acid and its conjugate base (or a weak base and its conjugate acid). Use the Henderson–Hasselbalch equation instead: pH = pKa + log([base]/[acid]). The salt hydrolysis formula applies only when the salt is the sole solute.

Related

Formula used
in m | Mass of salt | g | 4.10 | 0
in mm | Molar mass of salt | g/mol | 82.03 | 0.001
in v | Final solution volume | mL | 250 | 0.001
in pka | Acid pKa (conjugate acid) | - | 4.75 | 0
out c | Salt concentration | mol/L | m / mm / (v / 1000) | 4
out ph | pH of solution | - | 7 + 0.5 * (pka + log10(c)) | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →