molecalculator

Moles & Molar Mass

Sub Base Calculator UK: How to Estimate Materials

Calculator No. 01-6784 · Updated · Formula and assumptions shown below

Compacted sub-base volume 2.250 m³
Approximate aggregate mass
4.50 tonnes
= Compacted sub-base volume × Aggregate bulk density ÷ 1000
Length
5 m
Set in the form below
Width
3 m
Set in the form below
You enter
Length (m), Width (m), Compacted depth (mm), Aggregate bulk density (kg/m³)
You get
Compacted sub-base volume (m³), Approximate aggregate mass (tonnes)
Rounding
3 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A UK sub-base calculator estimates the compacted aggregate needed for a driveway, patio, path or other project, using the area and finished sub-base depth you enter. This calculator returns the required volume in cubic metres and an approximate bulk mass in tonnes; use local supplier data to confirm the actual loose quantity to order.

Formula

Compacted volume is length × width × depth, after converting depth from millimetres to metres: V = L × W × (D / 1000). Approximate mass is volume × the aggregate bulk-density estimate: M = V × ρ / 1000, converting kilograms to tonnes.

  • L = length in metres.
  • W = width in metres.
  • D = compacted depth in millimetres; dividing by 1000 converts it to metres.
  • V = geometric compacted volume in cubic metres.
  • ρ = assumed bulk density in kilograms per cubic metre. It varies with material, grading, moisture and how bulk density is reported.
  • M = estimated mass in metric tonnes; dividing kilograms by 1000 converts to tonnes.

The calculation treats the project as a rectangular, uniformly deep area. It does not calculate loose delivery volume, account for a shaped surface, or specify a suitable construction depth.

Worked Example

Using the calculator’s default values: length 5 m, width 3 m, compacted depth 150 mm and assumed bulk density 2,000 kg/m³:

  1. Convert depth: 150 mm / 1000 = 0.15 m.
  2. Calculate compacted volume: 5 m × 3 m × 0.15 m = 2.250 m³.
  3. Calculate estimated mass: 2.250 m³ × 2,000 kg/m³ / 1000 = 4.50 tonnes.

The calculator therefore gives 2.250 m³ of compacted sub-base and an approximate mass of 4.50 tonnes. The mass is only an estimate because the chosen density may not match the supplier’s product or moisture condition.

Assumptions

  • The area is rectangular, level and uniformly deep.
  • The entered depth is the depth after compaction, not the loose depth when delivered.
  • The density default of 2,000 kg/m³ is a planning assumption, not a universal property of sub-base.
  • The volume is a geometric estimate; it includes no allowance for over-excavation, uneven ground, edge losses or construction waste.

How to Use the Estimate

Measure the area that will actually receive the aggregate. For a simple rectangular driveway, use its length and width. For a path with a constant width, length × width gives its area; for an L-shaped or irregular layout, divide it into rectangles, calculate each section and add the volumes. Avoid measuring only the vehicle or paving surface if the base extends beyond it.

Enter depth in millimetres. Common design depths depend on the intended use and site conditions, so the calculator deliberately does not prescribe one. A drive carrying heavier vehicles, weak or wet ground, drainage needs, local specifications and the paving system can all affect the required build-up. Check the design or seek suitable construction advice rather than treating a common depth as a rule.

  • Measure several points if the ground or planned base is uneven. Use separate sections or a representative average depth where appropriate.
  • For a circular area, calculate its area separately (π × radius²), then multiply by depth; this rectangular calculator does not accept a radius directly.
  • Use the volume result to understand the compacted space to fill. Use the tonne result only as an initial material estimate.
  • Confirm the product’s sales unit and density basis with the supplier before ordering. A tonne and a cubic metre are not interchangeable without a relevant density.

Compacted Volume, Loose Volume and Ordering

The key distinction is between the finished compacted layer and aggregate delivered loose. Compaction rearranges particles and reduces the space between them, so the loose quantity needed to produce a specified compacted volume is generally greater. The calculator reports the finished geometric volume only; it does not apply a universal “compaction factor” because that factor depends on the material, grading, moisture, compaction method and site.

Do not simply order exactly the displayed volume and assume it will form that depth after compaction. Ask the supplier what loose volume or mass corresponds to the product and what allowance is suitable for the intended installation. If ordering by tonne, their product-specific bulk-density figure is more useful than the default estimate here. If ordering by cubic metre, establish whether the quoted amount refers to loose delivered material or another basis.

A practical check is to compare the supplier’s quoted delivery quantity with both outputs, then ask which one they use for billing. Keep a modest, project-appropriate allowance in mind for irregular edges and handling, but avoid adding an arbitrary percentage that could leave a large surplus.

Choosing Material and Preparing the Base

“Sub-base” describes a structural layer, not one single aggregate. In UK projects, a graded crushed aggregate commonly specified for sub-base may be sold under a specification or grading name; the appropriate choice depends on the project specification, ground and surface finish. Check that the material is intended for the use and that its grading and installation guidance suit the job. Recycled aggregates can also be suitable when they meet the required specification, but the label alone does not establish performance.

Before placing aggregate, plan the finished levels, edge restraint and water drainage. Water should not be directed towards buildings or neighbouring land in a way that creates a hazard or nuisance. Excavate to allow for the sub-base and the remaining layers, such as bedding and paving, rather than setting the sub-base depth from the final surface level alone. Place and compact the aggregate in suitable layers according to the project specification and equipment guidance; a single deep loose layer may not compact evenly.

Construction work can involve buried services, heavy loads, dust and machinery. Check for services before digging, use suitable protective equipment and follow relevant product and equipment safety instructions. For structural or drainage questions, use the applicable project specification or qualified advice.

Common Errors and Calculator Limits

  • Forgetting the depth conversion: 150 mm is 0.15 m, not 150 m. The calculator converts millimetres by dividing by 1000.
  • Using loose depth as compacted depth: enter the depth the finished sub-base should have, then obtain supplier guidance about loose delivery quantity.
  • Assuming density is exact: the tonne figure changes in direct proportion to density. If actual density is 1,800 kg/m³, for example, the same 2.250 m³ represents 4.05 tonnes, not 4.50.
  • Mixing units: length and width must be in metres, depth in millimetres, and density in kg/m³. Convert measurements before entering them.
  • Ignoring shape or slope: one length, width and depth cannot represent a complicated boundary or changing thickness exactly. Split the plan into simpler shapes and calculate separately.

Results are rounded for readability. The volume calculation is exact for the entered rectangular dimensions, but measurements and construction conditions are not exact. The mass conversion is especially approximate because the density input is an assumption. This tool is for estimating quantities, not for verifying ground strength, drainage design or compliance with a project specification.

Frequently Asked Questions

How much sub-base do I need for a 5 m by 3 m area?
At a compacted depth of 150 mm, the volume is 5 × 3 × 0.15 = 2.25 m³. The amount to order may be higher because delivered aggregate is loose; confirm the required quantity with the supplier.

How many tonnes are in a cubic metre of sub-base?
There is no single exact conversion. It depends on the aggregate and its condition. This calculator uses 2,000 kg/m³ as an editable planning assumption, equal to about 2 tonnes per cubic metre; use the supplier’s figure for an order.

Should I enter the loose or compacted depth?
Enter the planned finished, compacted depth. The tool calculates the volume of that finished layer, not the loose material volume needed before compaction.

Can I use this calculator for a patio or path?
Yes, if you enter the area’s dimensions and the specified compacted sub-base depth. It estimates material quantity, but does not determine the correct depth or replace the paving project’s specification.

Does the estimate include waste or extra material?
No. It calculates only the rectangular finished volume and estimated mass. Account separately for uneven ground, irregular edges and any supplier-recommended allowance.

Related

Formula used
in l | Length | m | 5 | 0
in w | Width | m | 3 | 0
in d | Compacted depth | mm | 150 | 0
in rho | Aggregate bulk density | kg/m³ | 2000 | 0
out v | Compacted sub-base volume | m³ | l * w * (d / 1000) | 3
out t | Approximate aggregate mass | tonnes | v * rho / 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →