This page explains the heat of dilution table for sulfuric acid (H₂SO₄), which lists the enthalpy change when concentrated acid is mixed with water to reach a given final concentration. You enter the initial and final concentrations (as weight percent H₂SO₄) and the calculator gives the enthalpy of dilution per mole of H₂SO₄, based on standard reference data. The result is the heat released (negative sign) or absorbed (positive sign) for that specific dilution step.
Formula
The enthalpy of dilution ΔHdil is the heat change when one mole of H₂SO₄ in a solution of concentration c₁ is diluted to concentration c₂ at constant temperature and pressure. It is expressed as:
ΔHdil = Hsolution(c₂) − Hsolution(c₁)
where Hsolution(c) is the partial molar enthalpy of H₂SO₄ in a solution of weight percent c. Because the absolute value of Hsolution is not directly measurable, tables report ΔHdil relative to a chosen reference state (usually infinite dilution or pure acid). The calculator above uses a linear approximation of the standard reference data for 25 °C: ΔHdil ≈ −41.3 + 0.12 × (c₁ − c₂) kJ/mol H₂SO₄. This is valid for dilutions from concentrated (≥90%) to moderate (≥20%) concentrations. For more precise work, consult the full tabulated data (e.g., from the NBS or Perry’s Chemical Engineers’ Handbook).
Worked Example
Using the default values: c₁ = 98.0 wt%, c₂ = 50.0 wt%, t = 25 °C.
ΔHdil = −41.3 + 0.12 × (98.0 − 50.0) = −41.3 + 0.12 × 48.0 = −41.3 + 5.76 = −35.54 kJ/mol H₂SO₄.
The negative sign means heat is released (exothermic). For a final solution of 50 wt% H₂SO₄, the mass of H₂SO₄ per kg of solution is 0.50 kg, which is 0.50 × 1000 / 98.079 = 5.098 mol H₂SO₄. So the heat released per kg of final solution is −35.54 × 5.098 = −181.2 kJ/kg. The calculator shows −181.2 kJ/kg (rounded to one decimal).
Assumptions
- The linear approximation is based on data at 25 °C; the heat of dilution varies slightly with temperature.
- The table assumes the final solution is homogeneous and that the mixing is done at constant pressure.
- The reference state is the pure liquid acid at the same temperature.
- The approximation is best for dilutions from concentrated acid (≥90 wt%) to final concentrations above 20 wt%. For very dilute final solutions (<5 wt%), the heat of dilution approaches a limiting value.
Why the Heat of Dilution Matters
Sulfuric acid dilution is strongly exothermic. When concentrated acid (98 wt%) is mixed with water, the heat released can raise the mixture to boiling if added too quickly. This is why the standard safety rule is “add acid to water, not water to acid”—adding water to concentrated acid can cause localized superheating and splattering. In industrial processes, the heat of dilution is used to design cooling systems for acid storage and dilution tanks. For example, diluting 1 kg of 98% acid to 50% releases roughly 180 kJ, enough to raise the temperature of the mixture by about 80 °C if no cooling is applied. Knowing the heat of dilution helps engineers size heat exchangers and predict temperature rises.
How to Use the Table in Practice
To use a full heat of dilution table, you typically look up the integral heat of solution for the initial and final concentrations. The difference gives the heat of dilution. For instance, if the integral heat of solution for 98 wt% acid is −73.5 kJ/mol and for 50 wt% acid is −38.0 kJ/mol, the dilution from 98% to 50% would have ΔH = −38.0 − (−73.5) = +35.5 kJ/mol? Actually, be careful with sign conventions. Most tables list the heat evolved when one mole of H₂SO₄ is dissolved in n moles of water. The heat of dilution is the difference between the heats of solution at the two concentrations. Always check the sign convention of your source.
Common Mistakes and Misconceptions
- Sign errors: A negative ΔH means exothermic (heat released). Some tables report heat evolved as positive, so you must invert the sign.
- Concentration units: The table is usually in weight percent, not molarity. Convert molarity to wt% using density.
- Temperature dependence: The heat of dilution changes with temperature. The table is typically for 25 °C; at other temperatures, a correction is needed (roughly 0.1 kJ/mol per 10 °C).
- Adding water to acid: This is dangerous because the heat is released rapidly at the water-acid interface, causing boiling and splashing. Always add acid to water slowly with stirring.
Alternatives and More Accurate Data
For precise engineering work, the linear approximation is not enough. Full tables list the integral heat of solution for every weight percent from 0 to 100 at various temperatures. These are available in standard references like the CRC Handbook of Chemistry and Physics or Perry’s Chemical Engineers’ Handbook. Alternatively, you can use thermodynamic software that models the H₂SO₄-H₂O system with activity coefficients. For quick estimates, the calculator above gives a reasonable value for most dilution scenarios.
Safety and Handling
Always follow your lab method, the safety data sheet (SDS) and your supervisor. When diluting sulfuric acid, wear appropriate PPE (goggles, acid-resistant gloves, apron). Add acid to water slowly while stirring. Never add water to concentrated acid. The heat of dilution can cause the solution to boil violently if not controlled. Use an ice bath or a cooling jacket for large dilutions. If the solution overheats, stop adding acid and allow it to cool.
Frequently Asked Questions
Why does sulfuric acid get so hot when diluted?
Because the hydration of H⁺ and SO₄²⁻ ions is strongly exothermic. The strong ion-dipole interactions between the ions and water molecules release a large amount of heat, much more than typical salts.
Is the heat of dilution the same as the heat of solution?
No. The heat of solution is the heat change when a solute dissolves in a solvent to form a solution of a specific concentration. The heat of dilution is the heat change when a solution of one concentration is diluted to a lower concentration. The heat of dilution is the difference between the heats of solution at the two concentrations.
Can I use this calculator for diluting other acids?
No. The heat of dilution is specific to each acid. For hydrochloric acid, the heat is lower; for nitric acid, it is also exothermic but different. This calculator only works for sulfuric acid.
What is the maximum temperature rise when diluting 98% acid to 50%?
Assuming no heat loss and starting at 25 °C, the adiabatic temperature rise is roughly ΔH / (mass × specific heat). For a 50 wt% solution, the specific heat is about 2.9 J/(g·°C). For 1 kg of final solution, the heat released is 181 kJ, giving a temperature rise of 181,000 / (1000 × 2.9) ≈ 62 °C, so the final temperature would be about 87 °C. In practice, with slow addition and cooling, it is lower.
Why does the table show a negative value for dilution?
Because the process is exothermic. By convention, negative ΔH means heat is released to the surroundings. If you see a table that lists positive values, it is likely reporting the heat evolved (as a positive number) rather than the enthalpy change.
Related
Formula used
in c1 | Initial concentration (wt% H₂SO₄) | % | 98.0 | 0 | 100 in c2 | Final concentration (wt% H₂SO₄) | % | 50.0 | 0 | 100 in t | Acid temperature | °C | 25 | 0 | 100 out dH | Enthalpy of dilution | kJ/mol H₂SO₄ | -41.3 + 0.12 * (c1 - c2) | 1 out dHkg | Enthalpy per kg of final solution | kJ/kg | dH * (c2 / 100) * 1000 / 98.079 | 1
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Relative Molecular Mass of Copper Sulfate0.0732 mol/L
- Bag Volume Calculator: How to Measure Any Bag25.50 L
- Molar Mass of Copper(II) Sulfate (CuSO₄)0.0468 mol/L
- Molar Mass of Hydrated Copper Sulphate (CuSO4·5H2O)0.0468 mol/L
- Molar Mass of CuSO4: How to Calculate It0.1000 mol
- Molar Mass of Copper(II) Sulfate: Exact Value & How to Find It0.0732 mol/L