This calculator converts a radioactive isotope’s half-life (the time for half the nuclei to decay) into its decay rate constant, λ (lambda), in reciprocal time units. You enter the half-life in any time unit, and the calculator returns λ in the matching reciprocal unit (e.g., s⁻¹, min⁻¹, yr⁻¹), plus the mean lifetime (τ). The relationship is λ = ln(2) / t₁/₂, where ln(2) ≈ 0.693147.
Formula
The decay rate constant λ (lambda) is defined by the radioactive decay law:
N(t) = N₀ · e−λt
where N(t) is the number of undecayed nuclei at time t, N₀ is the initial number, and e is Euler’s number (≈2.71828). The half-life t₁/₂ is the time when N(t₁/₂) = N₀/2, so:
N₀/2 = N₀ · e−λ·t₁/₂ → ln(1/2) = −λ·t₁/₂ → λ = ln(2) / t₁/₂
Here:
- λ = decay rate constant (units: reciprocal of time, e.g., s⁻¹, yr⁻¹)
- t₁/₂ = half-life (units: time, e.g., seconds, years)
- ln(2) = 0.6931471805599453 (dimensionless)
The mean lifetime τ is the average time a nucleus survives before decaying: τ = 1/λ = t₁/₂ / ln(2).
Worked Example
Using the default half-life of 5730 years (the approximate half-life of carbon-14):
- Write the formula: λ = ln(2) / t₁/₂
- Substitute t₁/₂ = 5730 years: λ = 0.693147 / 5730
- Calculate: λ = 0.000120968 yr⁻¹ (to 6 significant figures: 1.20968 × 10⁻⁴ yr⁻¹)
- Mean lifetime: τ = 5730 / 0.693147 = 8267 years (rounded to 4 significant figures)
The calculator gives λ = 0.000121 yr⁻¹ and τ = 8267 yr for these defaults, matching the manual calculation.
Assumptions
- Exponential decay: the decay probability per nucleus per unit time is constant (no chemical or physical influence).
- Single decay mode: the isotope decays by one pathway; if multiple modes exist (e.g., β⁻ and γ), λ represents the total decay constant.
- Time unit consistency: both λ and t₁/₂ must use the same time base (e.g., years for both).
When to Use This Conversion
You need λ when working with the exponential decay equation directly, for example:
- Calculating the activity (decays per second) of a sample: A = λN, where N is the number of radioactive nuclei.
- Determining the time for a sample to decay to a specific fraction: t = ln(N₀/N) / λ.
- Combining decay constants in decay chains (e.g., parent and daughter isotopes).
- Fitting experimental decay data to an exponential curve.
If you only need to know how much remains after a given time, you can use the half-life directly: N(t) = N₀ · (1/2)^(t/t₁/₂). The conversion to λ is useful when you need the rate itself, not just the fraction remaining.
How to Read the Result
The decay rate constant λ tells you the probability per unit time that a single nucleus will decay. For example, λ = 0.000121 yr⁻¹ means each carbon-14 nucleus has a 0.0121% chance of decaying in one year. The mean lifetime τ is the average time a nucleus exists before decaying; for carbon-14 it’s about 8267 years, which is longer than the half-life because the few nuclei that survive long times pull the average up.
Note that λ is not the same as the activity (A), which depends on how many nuclei you have. A sample with 1 gram of carbon-14 has a huge number of nuclei, so even a small λ produces many decays per second. The calculator gives you λ, not activity; to get activity you must multiply by N.
Common Mistakes and Pitfalls
- Unit mismatch: If you enter half-life in years but want λ in s⁻¹, you must convert years to seconds first (1 yr = 31,557,600 s). The calculator assumes the output unit matches the input unit; it does not auto-convert.
- Confusing λ with half-life: λ is a rate (probability per time), while t₁/₂ is a time. They are inversely related: a short half-life gives a large λ, and vice versa.
- Using natural log vs. log base 10: The formula uses natural logarithm (ln), not log₁₀. ln(2) ≈ 0.693, while log₁₀(2) ≈ 0.301. Using the wrong log gives a wrong λ.
- Rounding too early: If you round ln(2) to 0.693 and then divide by a small half-life, the error can be significant. Keep at least 6 significant figures in intermediate steps.
Limits of the Formula
The exponential decay law is a statistical description that applies to large numbers of nuclei (typically >10¹⁰). For very small samples (a few atoms), decay is a random process and you cannot predict exactly when a given nucleus will decay—only the probability. Also, the formula assumes the half-life is constant, which is true for most isotopes under normal conditions, but some isotopes can have their decay rates altered by extreme conditions (e.g., electron capture in different chemical states). For practical purposes, the formula is accurate for all standard laboratory and environmental applications.
Frequently Asked Questions
How do I convert half-life to decay rate in seconds?
First convert the half-life to seconds (e.g., 1 day = 86,400 s), then compute λ = 0.693147 / t₁/₂ (in seconds). The result will be in s⁻¹. For example, a half-life of 1 day gives λ = 0.693147 / 86400 ≈ 8.02 × 10⁻⁶ s⁻¹.
What is the difference between decay rate and decay constant?
Decay rate often refers to the activity (A), which is the number of decays per second in a sample (measured in becquerels, Bq). The decay constant λ is a property of the isotope, independent of sample size. Activity = λ × N, where N is the number of nuclei. So λ is like a per-nucleus probability rate, while activity is the total rate for the whole sample.
Can I use this calculator for any radioactive isotope?
Yes, as long as you know the half-life. The formula λ = ln(2)/t₁/₂ applies to any isotope that decays by a single exponential process. For isotopes with multiple decay branches, the total λ is the sum of the branch constants, but the overall decay still follows the same formula with the effective half-life.
Why is the mean lifetime longer than the half-life?
The half-life is the time for half the nuclei to decay, but some nuclei survive much longer. The mean lifetime is the average survival time of all nuclei, and because the decay curve has a long tail (some nuclei live many half-lives), the average is pulled up. Mathematically, τ = t₁/₂ / ln(2) ≈ 1.443 × t₁/₂, so it’s always about 44% longer.
How do I find the decay rate from a graph of activity vs. time?
Plot the natural log of activity (ln A) versus time. The slope of the straight line is −λ. Alternatively, if you have two points (t₁, A₁) and (t₂, A₂), use λ = ln(A₁/A₂) / (t₂ − t₁). This is a common experimental method to determine λ without waiting for a full half-life.