To convert standard cubic feet (scf) of a gas to litres, multiply the scf value by 28.3168. This gives the volume in litres at the same standard conditions (usually 60°F and 14.7 psia for natural gas). The calculator below does this conversion instantly, and the rest of this article explains the underlying gas laws, common pitfalls, and practical uses.
Formula
The conversion relies on the exact relationship between cubic feet and litres:
1 scf = 28.316846592 litres
This factor comes from the definitions: 1 foot = 0.3048 metres exactly, so 1 cubic foot = (0.3048)3 = 0.028316846592 m³. Since 1 m³ = 1000 L, 1 ft³ = 28.316846592 L. The calculator applies this factor directly to the input volume in scf.
In the calculator block: l = scf * 28.316846592 and m3 = l / 1000.
Worked Example
Using the default input of 100 scf:
- Start with 100 scf.
- Multiply by the conversion factor: 100 × 28.316846592 = 2831.6846592 L.
- Round to two decimal places: 2831.68 L.
- To get cubic metres: 2831.6846592 / 1000 = 2.8316846592 m³, rounded to 2.832 m³.
So 100 scf equals 2831.68 litres (or 2.832 m³).
Assumptions
- The conversion factor is exact and independent of gas type or conditions.
- “Standard cubic foot” is a measure of gas quantity at defined standard conditions, but those conditions vary by industry (see below). The calculator converts the volume only; it does not correct for temperature or pressure differences.
- No ideal gas assumption is needed for the pure unit conversion.
What Does “Standard” Mean in SCF?
The “standard” in standard cubic feet refers to a fixed set of temperature and pressure conditions. Unfortunately, there is no single universal standard. Common definitions include:
- 60°F and 14.7 psia (15.56°C, 101.325 kPa) – used widely in the US natural gas industry.
- 0°C and 101.325 kPa (32°F, 14.696 psia) – the older “normal” condition (Nm³).
- 15°C and 101.325 kPa – used in some international contexts.
- 20°C and 101.325 kPa – sometimes used in compressed gas specifications.
When you see “scf” on a gas cylinder or a flow meter, it means the gas volume has been adjusted to one of these reference conditions. The actual volume at your working pressure and temperature will be different. The conversion to litres is straightforward, but you must know which standard is being used to interpret the number correctly.
Why Convert SCF to Litres?
In many engineering and laboratory settings, gas volumes are reported in scf (especially in the US), while many scientific calculations and international standards prefer litres or cubic metres. Converting allows you to:
- Compare gas quantities from different sources that use different units.
- Calculate gas concentrations in a lab where volumes are measured in litres.
- Size gas storage or flow equipment that is specified in metric units.
- Convert gas flow rates (scf/min to L/min) for process design.
For example, if a gas chromatograph uses a carrier gas at 30 mL/min, and your supplier quotes the cylinder capacity in scf, you can convert to litres to estimate how long the cylinder will last.
Common Mistakes and Misconceptions
- Confusing scf with actual cubic feet (acf): acf is the volume at the actual pressure and temperature, not adjusted to standard. The conversion factor only applies to scf.
- Using the wrong standard: If you assume 60°F but the data is based on 0°C, the volume in litres will be off by about 5%. Always verify the reference conditions.
- Forgetting that gas volume depends on pressure and temperature: The litre value you get is the volume at standard conditions, not at your process conditions. To find the actual volume at a different P and T, you must use the ideal gas law: V₂ = V₁ × (P₁/P₂) × (T₂/T₁) (with absolute temperatures).
- Rounding too early: Use the full conversion factor (28.316846592) to avoid accumulating errors in multi-step calculations.
When to Use the Ideal Gas Law Instead
If you need to convert between scf and litres at non-standard conditions, or if you need to account for gas type (molecular weight), you must use the ideal gas law:
PV = nRT
where P is absolute pressure, V is volume, n is number of moles, R is the gas constant, and T is absolute temperature. For example, to find the volume of 1 mole of gas at standard conditions (60°F, 14.7 psia):
- Convert to SI: T = (60-32)×5/9 + 273.15 = 288.71 K, P = 14.7 psia × 6.89476 kPa/psi = 101.35 kPa.
- V = nRT/P = (1 mol × 8.31446 J/(mol·K) × 288.71 K) / 101350 Pa = 0.02366 m³ = 23.66 L.
- So 1 scf (at 60°F, 14.7 psia) is about 28.32 L, which corresponds to about 1.197 moles of gas (since 28.32/23.66 ≈ 1.197).
This is useful when you need to convert scf to mass (using molecular weight) or to moles for chemical reactions.
Practical Applications and Examples
Here are a few real-world scenarios where converting scf to litres matters:
- Natural gas billing: Your gas meter may read in hundreds of cubic feet (ccf), which is 100 scf. Converting to litres helps compare with metric bills.
- Laboratory gas cylinders: A typical E-size cylinder of nitrogen contains about 220 scf. That’s 220 × 28.3168 = 6230 L at standard conditions.
- Air compressor ratings: Compressor output is often given in scfm (standard cubic feet per minute). To get litres per minute, multiply by 28.3168. A 10 scfm compressor delivers 283 L/min at standard conditions.
- Environmental reporting: Emissions of gases are often reported in scf or standard cubic meters (scm). Converting to litres can help when comparing to regulatory limits expressed in metric units.
Frequently Asked Questions
Is 1 scf exactly equal to 28.3168 litres?
Yes, that is the exact conversion factor based on the definition of the foot and the litre. However, the actual gas volume at standard conditions depends on which standard you use (60°F vs 0°C etc.), but the unit conversion factor is constant.
Does the type of gas affect the scf to litre conversion?
No, the conversion is purely a unit change. One scf of helium and one scf of nitrogen both occupy 28.3168 litres at the same standard conditions. The gas type only matters if you need to convert to mass or moles.
How do I convert scf to cubic meters?
Divide the volume in litres by 1000. So 1 scf = 0.0283168 m³. The calculator above gives this as the second output.
What is the difference between scf and Nm³?
Both are standard volumes, but they use different reference conditions. scf typically uses 60°F and 14.7 psia, while Nm³ (normal cubic meter) uses 0°C and 101.325 kPa. To convert between them, you must adjust for the temperature difference using the ideal gas law. One scf is approximately 0.0268 Nm³, but the exact factor depends on the specific standards used.
Can I use this calculator for gas flow rates?
Yes, if you have a flow rate in scf per minute, you can multiply by 28.3168 to get litres per minute. The calculator works for any volume, including flow rates, as long as you treat the input as a volume per time.
Why do some sources use 28.32 and others 28.3168?
28.32 is a rounded value for convenience. For precise engineering calculations, use the full factor 28.316846592 to avoid rounding errors, especially when dealing with large volumes.
Related
Formula used
in scf | Volume in standard cubic feet (scf) | scf | 100 | 0 | 1000000 out l | Volume in litres (L) | L | scf * 28.316846592 | 2 out m3 | Volume in cubic metres (m³) | m³ | l / 1000 | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Relative Molecular Mass of Copper Sulfate0.0732 mol/L
- Bag Volume Calculator: How to Measure Any Bag25.50 L
- Molar Mass of Copper(II) Sulfate (CuSO₄)0.0468 mol/L
- Molar Mass of Hydrated Copper Sulphate (CuSO4·5H2O)0.0468 mol/L
- Molar Mass of Copper(II) Sulfate: Exact Value & How to Find It0.0732 mol/L
- Molar Mass of CuSO4: How to Calculate It0.1000 mol