molecalculator

Moles & Molar Mass

Half-Life Day One: What It Means & How to Play

Calculator No. 01-7041 · Updated · Formula and assumptions shown below

Molarity 0.2000 mol/L
Concentration in millimolar
200.00 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
58.44 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Half-Life: Day One is a promotional demo version of the original Half-Life (1998), released in 1998 alongside certain graphics cards and later included in the Game of the Year edition. It contains the first portion of the game, ending at the chapter “Unforeseen Consequences,” and serves as a playable introduction to the full title. If you own the demo, you play through the opening sequence of the Black Mesa Research Facility incident, from the resonance cascade to the point where you reach the surface, but the game stops there with a message directing you to buy the full version.

Formula

The calculator above computes molarity, the concentration of a solution in moles of solute per liter of solution. The formula is:

c = m / (M × V)

  • c = molarity (mol/L, often written M)
  • m = mass of solute (g)
  • M = molar mass of the solute (g/mol)
  • V = final volume of solution (L; convert from mL by dividing by 1000)

This is the standard definition of molarity: moles of solute divided by liters of solution. The calculator also outputs millimolar (mM), which is simply molarity multiplied by 1000.

Worked Example

Using the default values from the calculator above, prepare 250 mL of a sodium chloride (NaCl) solution by dissolving 2.922 g of NaCl. The molar mass of NaCl is 58.44 g/mol (Na = 22.99, Cl = 35.45).

  1. Convert volume to liters: 250 mL ÷ 1000 = 0.250 L
  2. Calculate moles of solute: 2.922 g ÷ 58.44 g/mol = 0.05000 mol (rounded to 5 significant figures)
  3. Divide moles by volume: 0.05000 mol ÷ 0.250 L = 0.2000 mol/L

The molarity is 0.2000 mol/L (or 0.2000 M). The calculator shows 0.2 mol/L with 4 decimal places, which is 0.2000. In millimolar, that is 200.00 mM. This matches the default output.

Assumptions

  • The solute is pure and dry (no water of hydration unless accounted for in the molar mass).
  • The final volume is the total solution volume after dissolution, not the volume of solvent added.
  • The solution is at a temperature where volume changes are negligible (usually 25 °C).
  • Complete dissolution occurs; no solute remains undissolved.

When to Use This Calculation

You need molarity whenever you prepare a solution for a reaction, a buffer, a culture medium, or a standard for calibration. For example, to make 500 mL of 0.1 M hydrochloric acid from a 12 M stock, you would use the dilution formula (M1V1 = M2V2) instead. The calculator here is for making a solution from a solid solute, not for diluting a concentrated liquid.

Typical lab tasks that use this calculation:

  • Preparing a salt solution for a biological buffer (e.g., PBS).
  • Making a standard solution for titration.
  • Dissolving a reagent to a known concentration for a kinetic study.

How to Read the Result

The first output is molarity in mol/L. A value of 0.2000 M means there are 0.2000 moles of solute in every liter of final solution. The second output is the same concentration in millimolar (mM), which is often more convenient for biological work. For example, 0.2000 M = 200.0 mM. If you are preparing a solution for a reaction that calls for 0.5 M, your result should match that target. If it does not, adjust the mass of solute or the final volume accordingly.

Common Mistakes and How to Avoid Them

  • Using solvent volume instead of final volume: If you add 250 mL of water to 2.922 g of NaCl, the final volume will be slightly more than 250 mL (because the salt adds volume). Always dissolve the solute in less water, then bring the total volume up to the mark in a volumetric flask.
  • Forgetting to convert mL to L: The formula requires liters. Dividing by 1000 is easy to forget. The calculator does this automatically.
  • Using the wrong molar mass: For hydrated salts (e.g., CuSO4·5H2O), include the water molecules in the molar mass. For NaCl, use 58.44, not 58.5 unless you are being approximate.
  • Rounding too early: Round only at the end. If you round intermediate steps, you may get a slightly different answer.

Limits of the Formula

Molarity changes with temperature because volume expands or contracts. For precise work, prepare the solution at the temperature where you will use it, or use molality (moles per kg of solvent) which is temperature-independent. Also, this formula assumes the solute dissolves completely and does not react with the solvent. For electrolytes like NaCl, the molarity is the concentration of the salt, not the concentration of individual ions (which would be 2× for NaCl because it dissociates into Na+ and Cl−).

Safety and Lab Practice

This calculator is for study and lab planning only. Always follow your lab method, the safety data sheet (SDS) for each chemical, and your supervisor’s instructions. Wear appropriate PPE (gloves, goggles, lab coat). When preparing acid solutions, always add acid to water, never the reverse. For any solution you make, label it with the chemical name, concentration, date, and your initials.

Frequently Asked Questions

What is the difference between molarity and molality?

Molarity (M) is moles of solute per liter of solution. Molality (m) is moles of solute per kilogram of solvent. Molality does not change with temperature because it depends on mass, not volume. For dilute aqueous solutions, the numerical values are similar, but they differ when the solute contributes significantly to volume.

How do I make a solution of a specific molarity from a solid?

Weigh the required mass of solute (mass = molarity × molar mass × volume in liters), dissolve it in a small amount of solvent in a volumetric flask, then add solvent up to the calibration mark. Mix thoroughly. This ensures the final volume is exact.

What if the solute is a hydrate?

Use the molar mass of the hydrated compound, which includes the water molecules. For example, CuSO4·5H2O has a molar mass of 249.69 g/mol, not 159.61 g/mol for anhydrous CuSO4. The mass you weigh out will be higher, but the number of moles of CuSO4 will be correct.

Can I use this for diluting a concentrated solution?

No. For dilutions, use the dilution equation M1V1 = M2V2. This calculator is for preparing a solution from a solid solute. If you have a stock solution, you need to calculate the volume of stock to dilute.

Why does my measured pH differ from the calculated pH?

The pH meter reading is the real check. Temperature and ionic strength shift pH, and the theoretical calculation assumes ideal behavior. Always calibrate the pH meter with standard buffers at the measurement temperature, and record the actual pH.

What is the molarity of pure water?

Pure water has a concentration of about 55.5 M (1000 g/L ÷ 18.015 g/mol). This is the molarity of water as a solvent, but it is rarely used in calculations because water is the solvent, not the solute.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →