molecalculator

Moles & Molar Mass

Half-Life Emulator: What It Is & How It Works

Calculator No. 01-7052 · Updated · Formula and assumptions shown below

Molarity 0.2000 mol/L
Concentration in millimolar
200.00 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
58.44 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A Half-Life emulator is a software program that lets you run the original Half-Life (1998) and its mods on modern hardware and operating systems where the original executable no longer works reliably. You enter the game files you already own, and the emulator translates the old game’s code and graphics calls into something your current Windows, Linux, or macOS system can run.

Formula

The molarity (concentration) of a solution is the amount of solute in moles divided by the volume of the solution in liters:

c = m / (M × V)

  • c – molarity, in mol/L (often written M)
  • m – mass of solute, in grams (g)
  • M – molar mass of the solute, in g/mol
  • V – final solution volume, in liters (L); if you have mL, divide by 1000

Worked Example

You need to prepare 250 mL of a sodium chloride (NaCl) solution with a concentration of 0.200 mol/L. The molar mass of NaCl is 58.44 g/mol. First convert the volume to liters:

V = 250 mL / 1000 = 0.250 L

Then calculate the required mass:

m = c × M × V = 0.200 mol/L × 58.44 g/mol × 0.250 L = 2.922 g

So you weigh out 2.922 g of NaCl, dissolve it in a small amount of water, and then add water until the final volume is exactly 250 mL. The calculator above gives the same result: entering 2.922 g, 58.44 g/mol, and 250 mL returns 0.2000 mol/L (200.0 mM).

Assumptions

  • The solute is pure and completely dissolves.
  • The final volume is the total solution volume, not the volume of solvent added.
  • Temperature and pressure do not affect molarity for solid solutes (they affect volume slightly, but this is ignored for routine lab work).
  • The molar mass is the formula weight of the anhydrous compound; hydrates require a different molar mass.

When to Use This Calculation

You use this whenever you need to prepare a solution with a specific molar concentration from a solid reagent. Common situations include making buffers, preparing stock solutions for dilutions, or making a reagent for a titration. The calculation is the same for any soluble solid compound – salt, sugar, a buffer salt, or a protein if you know its molar mass.

How to Read the Result

The result in mol/L tells you how many moles of solute are in every liter of final solution. A 0.200 mol/L NaCl solution contains 0.200 moles of NaCl per liter. The millimolar value (mM) is simply the molarity multiplied by 1000, which is convenient when working with small concentrations. For example, 0.200 mol/L = 200 mM.

Common Mistakes

  • Using mL instead of L – the formula requires liters. Always divide the volume in mL by 1000 first.
  • Forgetting the final volume – you must add solvent until the total volume reaches the mark, not just add the calculated mass to that volume of water.
  • Rounding too early – keep at least 4 significant figures in intermediate steps to avoid errors in the final concentration.
  • Using the wrong molar mass – check whether your compound is anhydrous or a hydrate (e.g., CuSO₄·5H₂O has a much higher molar mass than CuSO₄).

Limits of the Formula

This formula assumes ideal behavior – that the solute dissolves completely and that the volume of the solution is exactly the sum of solute and solvent volumes. For very concentrated solutions, the actual volume may differ slightly because the solute takes up space. Also, molarity changes with temperature because liquids expand and contract; if you need extreme precision, you would use molality (moles per kg of solvent) instead. For routine lab work, these effects are negligible.

Frequently Asked Questions

What is the difference between molarity and molality?

Molarity (mol/L) is moles of solute per liter of solution. Molality (mol/kg) is moles of solute per kilogram of solvent. Molality does not change with temperature, while molarity does, because the volume of the solution changes with temperature.

Can I use this calculator for any chemical?

Yes, as long as you know the molar mass of the solute. The molar mass is the sum of the atomic weights of all atoms in the formula. For example, NaCl = 22.99 + 35.45 = 58.44 g/mol.

What if I only have the mass and want to find the concentration?

You can rearrange the formula: c = m / (M × V). Enter the mass, molar mass, and volume, and the calculator will give you the molarity. That is exactly what this calculator does – you can enter any three of the four variables (m, M, V, c) and solve for the missing one, but this page is set up to compute molarity from mass, molar mass, and volume.

Do I need to add the solute to 250 mL of water or to make 250 mL of solution?

You need to make the final volume 250 mL. Dissolve the solute in less than 250 mL of water (e.g., 200 mL), then add water until the total volume reaches exactly 250 mL in a volumetric flask. Adding solute to 250 mL of water would give a slightly larger final volume and a lower concentration.

Why does the calculator ask for the final solution volume in mL?

Because most lab glassware is marked in mL, and the formula works in liters. The calculator converts mL to L internally (dividing by 1000). If you prefer to work in liters, you can enter the volume in L as well – just remember that 1 L = 1000 mL.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →