molecalculator

Moles & Molar Mass

Dilution Calculator: Find the Volume to Transfer

Calculator No. 01-6617 · Updated · Formula and assumptions shown below

Starting solution to transfer 10.000 mL
Approximate diluent volume
90.000 mL
= Final solution volume − Starting solution to transfer
Starting concentration
1 mol/L
Set in the form below
Target concentration
0.1 mol/L
Set in the form below
You enter
Starting concentration (mol/L), Target concentration (mol/L), Final solution volume (mL)
You get
Starting solution to transfer (mL), Approximate diluent volume (mL)
Rounding
3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This dilution calculator finds how much of a starting solution to transfer to make a chosen final concentration and volume. Enter the starting concentration, target concentration, and final solution volume; it returns the stock volume to use and the amount of diluent to add. The calculation assumes the same solute is being diluted and that you bring the mixture to the stated final volume.

Formula

The dilution relationship is C1V1 = C2V2. Rearranged to find the starting-solution volume:

V1 = C2V2 / C1

  • C1 is the starting concentration in mol/L.
  • V1 is the volume of starting solution to transfer, in mL.
  • C2 is the desired target concentration in mol/L.
  • V2 is the final solution volume in mL.

The equation works because the amount of solute is conserved during dilution: the starting solution contains the same amount of solute as the finished solution. The calculator uses the same concentration units for C1 and C2, so they cancel. The volume units also cancel in the ratio, leaving V1 in mL. The diluent estimate is V2 − V1; in practice, add diluent until the mixture reaches the final volume rather than assuming component volumes always add exactly.

Worked Example

Using the calculator’s default values:

  • Starting concentration, C1 = 1 mol/L
  • Target concentration, C2 = 0.1 mol/L
  • Final volume, V2 = 100 mL

Substitute into the rearranged equation:

V1 = (0.1 mol/L × 100 mL) / (1 mol/L) = 10 mL

The concentration units cancel, leaving volume. Transfer 10 mL of the 1 mol/L starting solution. The calculator’s second output estimates diluent as:

Vd = 100 mL − 10 mL = 90 mL

Thus, use 10 mL of starting solution and bring the total solution volume to 100 mL. The calculator displays 10.000 mL and 90.000 mL at its selected three decimal places.

Assumptions

  • The same solute is present before and after dilution, and no solute is lost, added, or chemically consumed.
  • The stated final volume is the total solution volume, not the amount of solvent alone.
  • Concentrations are expressed in matching units. The calculator uses mol/L for both.
  • The simple diluent estimate assumes additive volumes; accurate preparation relies on reaching the final volume mark.

What You’ll Need

  • The starting solution’s concentration and the desired final concentration, in the same units.
  • The intended final solution volume.
  • A reliable way to measure and transfer the calculated volume, plus a suitable vessel with a final-volume mark when precision matters.
  • The appropriate diluent and a label for the prepared solution.

For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor. Check that the starting solution is appropriate for the intended use and that the target concentration is attainable by dilution.

Step-by-Step

  1. Confirm the starting concentration. Read the solution label or preparation record and note the concentration and units. Do not assume a percentage, mass concentration, or molarity is interchangeable with another concentration type.
  2. Choose the target concentration and final volume. The target concentration must be positive and no greater than the starting concentration for an ordinary dilution. Decide how much finished solution is needed; this is the total final volume.
  3. Convert units if needed. Put both concentrations in the same units before using the equation. For example, convert 500 mM to 0.500 mol/L by dividing by 1000. Convert volume units consistently if calculating by hand; the calculator’s final volume field is in mL.
  4. Calculate the transfer volume. Use V1 = C2V2/C1, or enter the three values above. The first result is how much starting solution to transfer.
  5. Check that the answer is physically possible. The transfer volume should be greater than zero and no larger than the final volume. If it exceeds the final volume, check the concentrations and units; the target may be higher than the starting concentration and would require concentration or a different stock, not dilution.
  6. Measure the starting solution. Use suitable volumetric equipment and transfer the calculated amount into an appropriate container. If the calculated volume is too small to measure reliably, prepare a larger final volume or use a validated intermediate dilution.
  7. Add diluent, then make up to the final volume. Add most of the diluent first, mix as appropriate, and then add more until the total solution reaches the chosen final volume. Do not automatically add the estimated diluent volume if exact concentration matters, because mixing can change total volume slightly.
  8. Mix and label. Mix until the solution is uniform, using the method appropriate for the material. Label it with its identity, concentration, date, and any required handling information.

Common Mistakes

  • Mixing units: using a stock in mol/L and a target in mmol/L without conversion changes the answer by a factor of 1000. Convert both concentrations to the same unit first.
  • Confusing final volume with diluent volume: V2 is the total volume after dilution. It is not the volume of water or other diluent to add.
  • Reversing the concentration ratio: the transfer volume is target concentration times final volume, divided by starting concentration. A more concentrated stock should require less transfer volume.
  • Rounding too early: keep extra digits through the calculation, then round to a volume your measuring equipment can deliver accurately. The displayed decimals do not guarantee that level of experimental accuracy.
  • Applying the equation to unlike quantities: the formula assumes the concentration describes the same solute on both sides. It does not account for reactions, degradation, precipitation, or a change in chemical form.

Tips

  • Use the exact concentration stated for the stock, rather than a rounded value from memory. If the stock concentration is uncertain, the final concentration will be uncertain too.
  • For a desired concentration far below the stock, a direct transfer may be impractically small. A planned serial dilution can improve measurement, but calculate each stage and verify the cumulative dilution factor.
  • For a simple dilution factor, divide the starting concentration by the target concentration. For example, reducing 1 mol/L to 0.1 mol/L is a 10-fold dilution.
  • When accuracy is important, use a vessel designed to contain the final volume and bring the solution to its mark at the appropriate temperature specified by the method.
  • Keep records of the stock value, calculation, measured volume, final volume, and any intermediate steps so the preparation can be checked or repeated.

Troubleshooting

The calculated transfer volume is larger than the final volume: verify that the target is not greater than the starting concentration, and check for a unit mismatch or a misplaced decimal. Dilution cannot produce a more concentrated solution.

The required volume is too small to measure: choose a larger final batch if suitable, or use a documented intermediate dilution that gives measurable volumes. Do not round the transfer volume to zero.

The result seems unexpectedly high or low: recalculate with matching concentration units and confirm that the final volume is entered in mL. Check whether the stock value refers to the same solute and concentration basis as the target.

The finished volume is over the mark: do not assume removing some mixture restores the intended concentration. If the preparation must be accurate, remake it or follow an approved correction method; document any deviation.

The solution is cloudy, separates, or does not dissolve: the dilution equation cannot diagnose solubility or compatibility. Stop and check the material’s method and safety information before proceeding; do not use a visibly unsuitable preparation.

Frequently Asked Questions

What is the dilution formula?
C1V1 = C2V2. To find the volume of starting solution, rearrange it to V1 = C2V2/C1.

Does final volume mean the amount of water to add?
No. It means the total volume of the finished solution. Add diluent until the mixture reaches that volume.

Can I use different units for the two concentrations?
Only after converting them to the same unit. For example, convert mM to mol/L by dividing by 1000.

Can dilution make a solution more concentrated?
No. Dilution lowers concentration or leaves it unchanged if no diluent is added. To reach a higher concentration, use a more concentrated stock or an appropriate concentration method.

What does a 10-fold dilution mean?
It means the final concentration is one tenth of the starting concentration. The stock-to-target concentration ratio is 10:1.

Why might the actual concentration differ from the calculated value?
Measurement uncertainty, an inaccurate stock concentration, incomplete mixing, volume changes on mixing, or loss or reaction of solute can affect the result. The equation describes ideal solute conservation, not every experimental effect.

Related

Formula used
in c1 | Starting concentration | mol/L | 1 | 0.000000001
in c2 | Target concentration | mol/L | 0.1 | 0.000000001
in vf | Final solution volume | mL | 100 | 0
out vs | Starting solution to transfer | mL | c2 * vf / c1 | 3
out vd | Approximate diluent volume | mL | vf - vs | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →