molecalculator

Moles & Molar Mass

Liquid Oxygen Gallons to SCF Conversion

Calculator No. 01-7231 · Updated · Formula and assumptions shown below

Gas volume at 70°F, 1 atm 115.0 SCF
Gas volume at 70°F, 1 atm
3,257 L
= Liquid oxygen volume × 3257
Liquid oxygen volume
1 gal
Set in the form below
You enter
Liquid oxygen volume (gal)
You get
Gas volume at 70°F, 1 atm (SCF), Gas volume at 70°F, 1 atm (L)
Rounding
1 dp · 0 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

One gallon of liquid oxygen equals approximately 115 standard cubic feet (SCF) of gaseous oxygen at 70°F and 1 atmosphere. This article explains the conversion, the underlying physics, and how to use the calculator below to convert any volume of liquid oxygen to SCF.

Formula

The conversion is based on the density of liquid oxygen and the ideal gas law. At its boiling point (-297°F, 1 atm), liquid oxygen has a density of 9.52 lb/gal. One gallon therefore contains 9.52 lb of O2. The molar mass of O2 is 31.998 g/mol, so 9.52 lb equals 4320 g, which is 135.0 mol. Using the ideal gas law at 70°F (294.26 K) and 1 atm:

V = nRT/P = (135.0 mol)(0.0820574 L·atm/(mol·K))(294.26 K) / (1 atm) = 3260 L = 115.1 SCF

Thus, 1 gallon of liquid oxygen → 115 SCF (rounded to 3 significant figures). The calculator uses 115.0 SCF/gal, which is the commonly accepted industrial conversion factor.

Worked Example

Using the default input of 1 gallon:

  1. Mass of liquid oxygen: 1 gal × 9.52 lb/gal = 9.52 lb
  2. Convert to grams: 9.52 lb × 453.592 g/lb = 4318 g
  3. Moles of O2: 4318 g / 31.998 g/mol = 134.9 mol
  4. Volume at 70°F (294.26 K) and 1 atm: V = nRT/P = (134.9)(0.0820574)(294.26)/1 = 3257 L
  5. Convert to SCF: 3257 L × (1 ft³ / 28.3168 L) = 115.0 SCF

The calculator returns 115.0 SCF for 1 gallon, matching the standard factor.

Assumptions

  • Liquid oxygen is at its boiling point at 1 atm (-297°F), density 9.52 lb/gal.
  • Gaseous oxygen behaves as an ideal gas at 70°F and 1 atm.
  • Standard cubic foot (SCF) is defined at 70°F and 1 atm (not 60°F or 15°C, which are also used).
  • The conversion factor 115 SCF/gal is for pure oxygen; impurities would change the density slightly.

Why Convert Liquid to Gas?

Oxygen is often stored and transported as a cryogenic liquid because it occupies far less volume. One gallon of liquid becomes about 115 cubic feet of gas, a ratio of roughly 1:860 by volume. Industries use liquid oxygen for steelmaking, medical gas supply, water treatment, and rocket propulsion. Knowing the gas yield is essential for sizing storage tanks, piping, and ventilation systems. For example, a 500-gallon liquid oxygen tank will produce 500 × 115 = 57,500 SCF of gas when fully vaporized.

How the Conversion Works

The conversion relies on two physical facts: the density of liquid oxygen and the ideal gas law. Liquid oxygen is denser than water (9.52 lb/gal vs. 8.34 lb/gal for water). When it vaporizes, the molecules spread out enormously, occupying about 860 times the volume. The exact SCF per gallon depends on the temperature and pressure used for the “standard” condition. Common standards include 70°F (21.1°C) at 1 atm (used here), 60°F (15.6°C) at 1 atm, and 15°C at 1 atm. The differences are small (a few percent), but for precise engineering work you must know which standard is being used.

Common Mistakes and Misconceptions

  • Mixing up SCF with actual cubic feet (ACF): SCF is a fixed reference condition; ACF is the volume at actual pressure and temperature. At high pressure, ACF is much smaller than SCF.
  • Using the wrong density: Liquid oxygen density varies slightly with temperature and pressure. The 9.52 lb/gal figure is for the normal boiling point at 1 atm. At higher pressure, the density increases.
  • Forgetting to convert pounds to moles: The ideal gas law requires moles, not mass. Always divide the mass by the molar mass (31.998 g/mol for O2).
  • Assuming 1 gallon of liquid = 1 gallon of gas: The volume ratio is about 1:860, not 1:1.

Practical Applications and Examples

Consider a hospital that uses liquid oxygen for patient care. A typical 1,000-gallon tank holds enough oxygen to produce 115,000 SCF of gas. At a usage rate of 500 SCF per hour, that tank lasts 230 hours (about 9.6 days). In welding and cutting, oxygen is often supplied as liquid in cylinders or bulk tanks; knowing the SCF content helps estimate how many cutting jobs can be done. For aerospace, liquid oxygen is used as an oxidizer; the SCF equivalent is used in engine test calculations.

Safety and Handling Considerations

Liquid oxygen is extremely cold (-297°F) and can cause severe frostbite on contact. It is also a strong oxidizer: materials that are normally combustible (like oil, grease, or wood) can ignite violently in the presence of high oxygen concentrations. Never allow liquid oxygen to spill on asphalt, clothing, or other organic materials. Always use equipment rated for oxygen service and ensure adequate ventilation to prevent oxygen enrichment. When converting volumes, always work in a well-ventilated area and follow your facility’s safety procedures and the safety data sheet (SDS) for oxygen.

Frequently Asked Questions

What is the exact conversion factor for liquid oxygen gallons to SCF? The commonly used factor is 115 SCF per gallon at 70°F and 1 atm. Some references use 114.8 or 115.3 depending on the standard temperature. For most purposes, 115 is accurate to within 1%.

Why is liquid oxygen measured in gallons but gas in SCF? Gallons are a convenient unit for cryogenic liquids, while SCF is used for gases to provide a consistent measure of the amount of gas at standard conditions. This is similar to how natural gas is billed in therms or CCF.

Does the conversion change with altitude or weather? Yes, because the actual gas volume depends on pressure and temperature. SCF is a fixed reference, but if you need actual cubic feet at your local conditions, you must apply the ideal gas law with your local pressure and temperature.

How many liters of gas does one liter of liquid oxygen produce? One liter of liquid oxygen (weighing about 1.141 kg) produces about 861 liters of gas at 70°F and 1 atm. This is the same volume ratio as gallons to SCF.

Can I use this calculator for other cryogenic liquids like nitrogen or argon? No, each liquid has a different density and molar mass. For nitrogen, the factor is about 93 SCF per gallon; for argon, about 105 SCF per gallon. You need the specific density and molar mass for each substance.

What is the difference between SCF and standard cubic meters (SCM)? SCF uses cubic feet at 70°F and 1 atm; SCM uses cubic meters at 15°C and 1 atm. One SCM equals 35.3147 SCF. Always check which standard your supplier or customer uses.

Related

Formula used
in gal | Liquid oxygen volume | gal | 1 | 0
out scf | Gas volume at 70°F, 1 atm | SCF | gal * 115.0 | 1
out liters | Gas volume at 70°F, 1 atm | L | gal * 3257 | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →