This calculator converts a rotational speed given in revolutions per minute (RPM) into the equivalent frequency in rotations per second (rev/s, also written as Hz when referring to rotational cycles). You enter the RPM value, and you get the rotations per second instantly, along with the result in radians per second for context.
Formula
The conversion is a simple unit change based on the definition of the minute:
Rotations per second (rev/s) = RPM ÷ 60
Where:
- RPM = revolutions per minute (rev/min), the input value.
- 60 = the number of seconds in one minute (s/min).
For angular velocity in radians per second (rad/s), the related formula is:
Angular velocity (rad/s) = RPM × 2π ÷ 60
because one full revolution equals 2π radians (about 6.2832 rad).
Worked Example
Using the default input of 1200 RPM:
- Write the conversion formula: rps = RPM ÷ 60.
- Substitute the value: rps = 1200 ÷ 60.
- Calculate: rps = 20.0000 rev/s.
For angular velocity: rad/s = 1200 × 2π ÷ 60 = 1200 × 6.283185307 / 60 = 125.6637 rad/s (rounded to 4 decimals).
Assumptions
- The input is a positive rotational speed (non-negative).
- The conversion uses the exact relationship 1 minute = 60 seconds.
- One revolution is exactly 2π radians.
- No mechanical losses or slip are considered; the value is a kinematic conversion.
Why Convert RPM to Rotations Per Second?
RPM is the most common unit for rotational speed in everyday machinery—car engines, hard drives, fans, and washing machine drums. However, many physics and engineering calculations use SI units, where angular velocity is in radians per second (rad/s) and frequency in hertz (Hz, which is the same as rev/s for rotational cycles). Converting RPM to rev/s is often the first step before calculating torque, power, or centripetal acceleration. For example, if a motor spins at 3000 RPM, it completes 50 full rotations every second—a number that is more intuitive when thinking about how many times a blade passes a point per second.
How the Conversion Works
The conversion is purely arithmetic because both units measure the same physical quantity: the number of complete rotations per unit time. A minute has 60 seconds, so any speed in RPM is simply divided by 60 to get rev/s. The reverse conversion multiplies by 60. This is a linear relationship: doubling the RPM doubles the rev/s. The calculator also outputs angular velocity in rad/s, which is the standard unit in physics equations like ω = 2πf, where ω is angular velocity and f is frequency in Hz. For example, a frequency of 20 rev/s corresponds to ω = 2π × 20 ≈ 125.66 rad/s.
Common Mistakes and Misconceptions
- Forgetting the 60: A frequent error is to treat RPM and rev/s as if they were the same, leading to answers 60 times too large. Always divide by 60.
- Confusing rev/s with rad/s: Rev/s counts whole rotations; rad/s measures the angle swept per second. One rev/s equals 2π rad/s. Using the wrong one in torque or power formulas will give wildly incorrect results.
- Rounding too early: In multi-step calculations, rounding the intermediate rev/s value to a whole number can introduce errors. Keep at least 4 significant figures until the final answer.
- Negative RPM: The calculator allows only non-negative inputs because rotational speed is typically expressed as a magnitude. If direction matters, use a signed value in rad/s separately.
When to Use rev/s vs. RPM
Choose the unit based on your context. RPM is standard for consumer specs and mechanical engineering in many industries (e.g., motor nameplates). Rev/s (or Hz) is preferred in physics, audio (vinyl turntables at 33⅓ RPM ≈ 0.556 rev/s), and when calculating frequencies for vibration analysis. For example, a hard drive spinning at 7200 RPM operates at 120 rev/s, which is useful to know for estimating bearing wear cycles. If you are working with the formula P = τ × ω (power = torque × angular velocity), you must use ω in rad/s, so convert RPM to rad/s first. The calculator gives both, saving you a step.
Practical Examples
- Car engine at idle: 800 RPM → 800 ÷ 60 = 13.33 rev/s.
- Centrifuge at 10,000 RPM → 10,000 ÷ 60 = 166.67 rev/s (about 1047 rad/s).
- Turntable at 33⅓ RPM → 33.333 ÷ 60 = 0.5556 rev/s (the standard 33⅓ RPM is exactly 5/9 rev/s).
- Drone propeller at 12,000 RPM → 200 rev/s.
These examples show that the conversion works identically for any RPM value, from slow turntables to high-speed spindles.
Limitations of the Formula
The conversion is exact and universal; it does not depend on the object’s size, mass, or material. However, it only gives the rotational frequency, not the linear speed of a point on the object. To find linear speed (v = ω × r), you need the radius. Also, the calculator assumes a constant speed; it does not handle acceleration or variable motion. For real machinery, the actual rotational speed may fluctuate slightly due to load, but the conversion remains valid at any instant.
Frequently Asked Questions
Is rev/s the same as Hz?
Yes, for rotational motion, 1 revolution per second equals 1 hertz (Hz). The hertz unit is defined as one cycle per second, and a full revolution is one cycle. So a motor spinning at 60 rev/s is operating at 60 Hz, which is why AC motors in countries with 60 Hz power often run at multiples of 60 rev/s under no load.
How do I convert rev/s back to RPM?
Multiply the rev/s value by 60. For example, 20 rev/s × 60 = 1200 RPM. This is the inverse of the division used in the forward conversion.
What is the difference between RPM and rad/s?
RPM is a count of whole revolutions per minute, while rad/s measures the angle (in radians) swept per second. Since one revolution is 2π radians, 1 RPM equals 2π/60 ≈ 0.10472 rad/s. Physicists prefer rad/s because it makes formulas for torque and power simpler.
Can I use this calculator for any rotating object?
Yes, the conversion is purely mathematical and applies to any object that rotates—wheels, gears, fans, motors, planets, or even subatomic particles. The only requirement is that the speed is given in RPM.
Why does my machine spec list RPM but not rev/s?
RPM is a long-standing convention in engineering and consumer products, likely because the numbers are larger and more intuitive for typical speeds (e.g., 3600 RPM sounds more impressive than 60 rev/s). The conversion is trivial, so manufacturers rarely list both.
Does the conversion change with temperature or pressure?
No. The relationship between minutes and seconds is fixed, and a revolution is always 2π radians. Temperature or pressure might change the actual speed of a physical motor, but the conversion factor between units remains constant.
Related
Formula used
in rpm | Rotational speed | RPM | 1200 | 0 out rps | Rotations per second | rev/s | rpm / 60 | 4 out rads | Angular velocity | rad/s | rpm * 2 * pi / 60 | 4
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Relative Molecular Mass of Copper Sulfate0.0732 mol/L
- Bag Volume Calculator: How to Measure Any Bag25.50 L
- Molar Mass of Copper(II) Sulfate (CuSO₄)0.0468 mol/L
- Molar Mass of Hydrated Copper Sulphate (CuSO4·5H2O)0.0468 mol/L
- Molar Mass of CuSO4: How to Calculate It0.1000 mol
- Molar Mass of Copper(II) Sulfate: Exact Value & How to Find It0.0732 mol/L