molecalculator

Moles & Molar Mass

SCF to Lbs: Gas Volume to Weight Conversion

Calculator No. 01-7291 · Updated · Formula and assumptions shown below

Mass 7.6488 lb
Amount of gas
119.76 mol
Result, rounded to 2 decimal places
Gas volume
100 SCF
Set in the form below
Molar mass of gas
28.97 g/mol
Set in the form below
You enter
Gas volume (SCF), Molar mass of gas (g/mol), Standard temperature (°C), Standard pressure (atm)
You get
Mass (lb), Amount of gas (mol)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Standard cubic feet (SCF) of a gas is a volume measurement at a defined temperature and pressure, and converting it to pounds (lbs) requires knowing the gas’s molecular weight and the standard conditions used. The conversion is not a single fixed number; it depends entirely on which gas you are measuring and which standard you are using. This calculator works out the mass in pounds from a gas volume in SCF using the ideal gas law, letting you enter the gas’s molar mass and the standard temperature and pressure.

Formula

The conversion uses the ideal gas law, PV = nRT, rearranged to solve for the number of moles (n), then multiplied by the molar mass to get mass in grams, then converted to pounds.

Mass (lb) = [V × 0.028316846592 × P × (M / 1000)] / (R × T) × 2.2046226218

  • V = gas volume in standard cubic feet (SCF)
  • 0.028316846592 = conversion factor from cubic feet to cubic meters (m³/ft³)
  • P = standard pressure in atmospheres (atm)
  • M = molar mass of the gas in g/mol (entered as g/mol, divided by 1000 to get kg/mol)
  • R = ideal gas constant, 8.31446261815324 J/(mol·K)
  • T = standard temperature in kelvin (K), calculated as °C + 273.15
  • 2.2046226218 = conversion factor from kilograms to pounds (lb/kg)

Worked Example

Using the default values from the calculator: 100 SCF of air (molar mass 28.97 g/mol) at 15 °C and 1 atm pressure.

Step 1: Convert SCF to cubic meters: 100 × 0.028316846592 = 2.8316846592 m³

Step 2: Convert temperature to kelvin: 15 + 273.15 = 288.15 K

Step 3: Convert molar mass to kg/mol: 28.97 / 1000 = 0.02897 kg/mol

Step 4: Calculate moles using PV = nRT: n = (2.8316846592 × 101325) / (8.31446261815324 × 288.15) = 286,921.5 / 2,395.8 ≈ 119.76 mol

Step 5: Calculate mass in kg: 119.76 × 0.02897 = 3.469 kg

Step 6: Convert to pounds: 3.469 × 2.2046226218 = 7.648 lb

The calculator returns 7.648 lb for these inputs.

Assumptions

  • The gas behaves as an ideal gas (valid for most gases at standard conditions, less so for high-pressure or low-temperature cases).
  • The gas is pure; if it is a mixture (like air), the molar mass must be the average molar mass of the mixture.
  • The standard conditions are those you enter; different industries use different standards (see below).
  • Compressibility factor (Z) is assumed to be 1, which is accurate for near-ideal conditions.

Why Standard Conditions Matter

The phrase “standard cubic foot” is ambiguous because there is no single universally accepted standard temperature and pressure. Different industries and countries define “standard” differently:

  • 15 °C (59 °F) and 1 atm: Common in natural gas and petroleum industries (ISO 13443, GPA 2177).
  • 0 °C (32 °F) and 1 atm: Used in some scientific and older engineering contexts (often called “normal” conditions).
  • 20 °C (68 °F) and 1 atm: Used in some European standards and for compressed air.
  • 60 °F (15.56 °C) and 14.696 psia: Common in US oil and gas (API).

The difference between 0 °C and 15 °C standards is about 5.5% in mass for the same SCF number. If you are comparing gas quantities from different sources, always check which standard they used; otherwise, your conversion could be off by several percent.

Common Gases and Their Molar Masses

To use the calculator, you need the molar mass of the gas. Here are common values (IUPAC abridged atomic weights):

  • Air (average): 28.97 g/mol
  • Nitrogen (N₂): 28.014 g/mol
  • Oxygen (O₂): 31.998 g/mol
  • Carbon dioxide (CO₂): 44.009 g/mol
  • Methane (CH₄): 16.043 g/mol
  • Hydrogen (H₂): 2.016 g/mol
  • Helium (He): 4.003 g/mol
  • Propane (C₃H₈): 44.097 g/mol

For a gas mixture, calculate the average molar mass by summing each component’s molar mass times its mole fraction. For example, dry air is roughly 78% N₂, 21% O₂, and 1% Ar, giving 0.78×28.014 + 0.21×31.998 + 0.01×39.948 ≈ 28.97 g/mol.

How to Choose the Right Standard

When performing an SCF to lbs conversion, the first question to ask is: what standard does the gas volume refer to? If the gas is being purchased, the supplier’s invoice or contract will state the standard conditions. If you are filling a cylinder, the volume is often listed at 21 °C and 1 atm (or “normal liters”). If you are doing engineering calculations for a pipeline, the API standard (60 °F, 14.696 psia) is typical in the US.

If no standard is specified, use 15 °C and 1 atm as a reasonable default, but note the assumption. For precise work, always confirm the conditions with the source of the volume measurement.

Common Mistakes and Misconceptions

A frequent error is treating SCF as if it were a mass unit. SCF is a volume, and the mass of gas in that volume changes with temperature and pressure. Another common mistake is using the wrong molar mass—for example, using the atomic mass of carbon (12.011) instead of the molecular mass of CO₂ (44.009).

Another misconception is that 1 SCF of any gas weighs the same. That is false: 1 SCF of hydrogen weighs about 0.0053 lb, while 1 SCF of propane weighs about 0.116 lb at the same conditions—a 22-fold difference. Always use the specific gas’s molar mass.

Rounding errors also creep in when people use approximate constants (like 8.314 instead of 8.3144626, or 0.0283 instead of 0.028316846592). For most purposes these are negligible, but for billing or regulatory compliance, use the full constants.

Limits of the Ideal Gas Law

The ideal gas law assumes no intermolecular forces and negligible molecular volume. For real gases at standard conditions (around 1 atm and 15 °C), most common gases deviate by less than 1% from ideal behavior. However, at high pressures (above 10 atm) or near the liquefaction point, the deviation grows. For example, CO₂ at 1 atm and 0 °C deviates by about 1.2% from ideal. For highly accurate work with real gases, you would introduce the compressibility factor Z into the equation (PV = ZnRT), where Z is gas-specific and depends on pressure and temperature. This calculator assumes Z = 1, which is appropriate for standard conditions.

Also note that this conversion gives the mass of the gas itself, not the weight of any container. If you are weighing a cylinder, you must subtract the tare weight (empty cylinder weight) to get the gas mass.

Frequently Asked Questions

How many pounds is 1 SCF of natural gas?

Natural gas is mostly methane (CH₄), with small amounts of ethane and other hydrocarbons. Using an average molar mass of about 17 g/mol (for pipeline-quality gas), 1 SCF at 15 °C and 1 atm weighs approximately 0.045 lb. At 60 °F and 14.696 psia, it is about 0.044 lb. The exact value depends on the gas composition and the standard conditions.

Is SCF the same as CF?

No. CF (cubic feet) is simply a volume at whatever temperature and pressure the gas happens to be. SCF (standard cubic feet) is the volume the gas would occupy at a defined standard condition. A gas at high pressure in a pipe might occupy 100 CF, but when corrected to standard conditions, it might only be 10 SCF. The correction accounts for compressibility and thermal expansion.

What is the difference between SCF and SCM?

SCF is standard cubic feet (imperial), while SCM is standard cubic meters (metric). One SCM equals 35.3147 SCF. The conversion between them is purely a unit conversion of volume; the mass per SCM is 35.3147 times the mass per SCF for the same gas and same standard conditions.

Can I use this calculator for liquids or solids?

No. This calculator is specifically for gases. Liquids and solids are nearly incompressible, so their volume does not change significantly with pressure, and their density is typically given directly in mass per volume (e.g., lb/gal or kg/L). For a liquid, you would simply multiply the volume by the density.

Why does the calculator ask for molar mass instead of just giving a fixed conversion factor?

Because the conversion factor is different for every gas. A fixed factor would only work for one specific gas at one specific standard condition. By letting you enter the molar mass and the standard conditions, the calculator works for any gas and any standard. If you are always working with the same gas, you can note the result for that gas and reuse it.

How accurate is this for high-pressure gas storage?

At high pressures (e.g., 200 bar in a cylinder), the ideal gas law overestimates the mass by 5–15% depending on the gas. For accurate high-pressure calculations, you need the compressibility factor Z for that gas at that pressure and temperature. This calculator is intended for standard or near-standard conditions, not for high-pressure cylinder fill calculations.

Related

Formula used
in v | Gas volume | SCF | 100 | 0
in mm | Molar mass of gas | g/mol | 28.97 | 0.001
in t | Standard temperature | °C | 15 | -273.15
in p | Standard pressure | atm | 1 | 0
out m | Mass | lb | v * 0.028316846592 * (p * 101325) * (mm / 1000) / (8.31446261815324 * (t + 273.15)) * 2.2046226218 | 4
out mol | Amount of gas | mol | v * 0.028316846592 * (p * 101325) / (8.31446261815324 * (t + 273.15)) | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →