molecalculator

Moles & Molar Mass

SCF to Liter Conversion: Gas Volume Explained

Calculator No. 01-7292 · Updated · Formula and assumptions shown below

Volume in liters 2,831.68 L
Volume in cubic meters
2.832 m³
= Volume in liters ÷ 1000
Volume in SCF
100 SCF
Set in the form below
You enter
Volume in SCF (SCF)
You get
Volume in liters (L), Volume in cubic meters (m³)
Rounding
2 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator converts a gas volume in standard cubic feet (SCF) to liters (L) at the same standard conditions. You enter the SCF value, and you get the equivalent volume in liters, plus the result in cubic meters for larger industrial quantities. The conversion is a fixed unit conversion, not a gas-law calculation, because SCF already specifies a set of temperature and pressure.

Formula

The conversion is a direct unit multiplication:

Liters = SCF × 28.316846592

Where:

  • SCF = volume in standard cubic feet (ft³ at standard conditions)
  • Liters = volume in liters (L)
  • 28.316846592 = exact number of liters in one cubic foot (1 ft³ = 28.316846592 L)

The same factor works for cubic meters: 1 ft³ = 0.028316846592 m³. This is a pure unit conversion, so it does not depend on the gas type, temperature, or pressure—as long as both the SCF and the liter volume refer to the same standard conditions.

Worked Example

Using the default value of 100 SCF:

  1. Start with the volume: 100 SCF
  2. Multiply by the conversion factor: 100 × 28.316846592 = 2831.6846592 L
  3. Round to two decimal places: 2831.68 L
  4. For cubic meters: 2831.6846592 ÷ 1000 = 2.8316846592 m³, rounded to 2.832 m³

The calculator shows 2831.68 L and 2.832 m³ for 100 SCF.

Assumptions

  • The conversion is purely volumetric; no gas-law correction is applied.
  • Both SCF and liters are measured at the same standard conditions (typically 60 °F and 14.696 psia, or 15 °C and 101.325 kPa, depending on the standard used).
  • No temperature or pressure compensation is needed because SCF already normalizes the gas to a reference state.

What Does “Standard” Mean in SCF?

Standard cubic feet is a measure of gas volume at a defined reference condition, not at the actual condition of the gas. The most common standard in the United States is 60 °F (15.56 °C) and 14.696 psia (one atmosphere). Many international standards use 15 °C (59 °F) and 101.325 kPa. Some older or European references use 0 °C (32 °F) and 101.325 kPa—this is often called “normal” cubic meters (Nm³) rather than SCF. The numerical value of SCF changes with the chosen standard, but the conversion factor to liters does not, because it is a fixed unit relationship. If you compare SCF from different standards, the actual gas quantities differ by a few percent, so always confirm which standard your SCF number uses.

Why Convert SCF to Liters?

Industries that measure gas flow—natural gas pipelines, compressed air systems, industrial gas suppliers, and laboratory gas handling—often report volumes in SCF because it gives a consistent measure of gas quantity independent of temperature and pressure. However, many engineering calculations, laboratory protocols, and international specifications use liters or cubic meters. Converting SCF to liters is needed when:

  • Comparing a US-spec gas volume with a European or Asian specification in liters.
  • Calculating the volume of gas a cylinder will deliver at standard conditions.
  • Converting flow rates from SCFM (standard cubic feet per minute) to liters per minute for equipment sizing.
  • Preparing gas mixtures where component volumes are given in different units.

For example, if a compressed gas cylinder label says it contains 250 SCF of nitrogen, that equals 250 × 28.316846592 = 7080.21 liters at standard conditions. That is the volume the gas would occupy if released to standard pressure and temperature.

Common Mistakes and Misconceptions

A frequent error is treating SCF as an actual physical volume at the gas’s current state. If a gas is compressed to 3000 psi in a cylinder, the cylinder’s internal volume is much smaller than the SCF rating. SCF is a “gas quantity” measure, not a container size. Another mistake is mixing standard conditions: converting an SCF measured at 60 °F to a liter volume at 0 °C without adjusting the gas law. The unit conversion alone is correct only when both sides use the same reference. Also, some people use the rounded factor 28.32 L/ft³, which introduces a small error of about 0.01%—fine for rough work but not for precise metering. Finally, remember that SCF is for gas, not liquid; liquid volumes in cubic feet convert using the same 28.316846592 factor, but the physical meaning is different.

How to Choose the Right Standard

Before converting, identify which standard your SCF value uses. The three common references are:

  • 60 °F, 14.696 psia – the US natural gas and compressed gas industry standard.
  • 15 °C, 101.325 kPa – the ISO standard used widely in Europe and for international trade.
  • 0 °C, 101.325 kPa – the “normal” condition used for Nm³, common in chemical engineering.

If your SCF comes from a US supplier, it is almost certainly 60 °F and 14.696 psia. If it comes from an international standard, it may be 15 °C. The conversion factor to liters is the same regardless, but if you need to compare gas quantities between standards, you must apply the ideal gas law to correct for the temperature difference. For example, 1 SCF at 60 °F equals about 0.948 SCF at 15 °C for the same number of gas molecules. Always state which standard you used when reporting converted volumes.

Related Conversions and Practical Use

Beyond SCF to liters, you may need other gas unit conversions:

  • SCFM to L/min: multiply SCFM by 28.316846592 to get liters per minute.
  • SCF to Nm³: first convert SCF to liters, then divide by 1000 to get cubic meters, then apply the standard-condition correction if the reference temperatures differ.
  • SCF to moles: at 60 °F and 14.696 psia, one mole of ideal gas occupies about 23.8 L, so 1 SCF ≈ 1.195 moles. This is useful for stoichiometric calculations.

In practice, this conversion appears in gas flow meter calibration, environmental reporting (e.g., emissions in SCF converted to metric units), and when ordering gas cylinders from suppliers who quote in SCF while your lab uses liters. Always double-check the standard condition note on the supplier’s certificate—it is the single most common source of error in gas volume conversions.

Limits of the Conversion

This conversion is exact for the unit relationship, but it inherits the limitations of the SCF definition. Real gases deviate from ideal behavior at high pressures or low temperatures; the standard conditions are chosen to minimize this, but for very accurate work at high pressure, a compressibility factor (Z) is needed. Also, if the gas contains moisture, the “wet” SCF includes water vapor volume, while a “dry” SCF does not—these differ by a few percent depending on humidity. For most engineering and laboratory purposes, the simple factor is sufficient, but for custody transfer or legal metering, always use the exact standard and any correction factors specified by the governing regulation.

Frequently Asked Questions

Is 1 SCF equal to 28.32 liters? Yes, 1 standard cubic foot equals 28.316846592 liters exactly. The rounded value 28.32 is commonly used and is accurate to about 0.01%.

Does the gas type matter for SCF to liter conversion? No. The conversion is purely a unit change from cubic feet to liters. The gas type only matters if you need to convert SCF to mass (using molecular weight) or to adjust for non-standard conditions.

What is the difference between SCF and Nm³? SCF typically refers to 60 °F and 14.696 psia, while Nm³ (normal cubic meters) refers to 0 °C and 101.325 kPa. They are different reference conditions, so the same physical gas quantity has a different numerical value in each unit. To convert, you must apply the ideal gas law to account for the temperature difference.

How do I convert SCFM to liters per minute? Multiply the SCFM value by 28.316846592. For example, 10 SCFM = 10 × 28.316846592 = 283.17 L/min.

Can I use this conversion for liquid volumes? The factor 28.316846592 L per cubic foot is valid for any volume, liquid or gas. However, SCF specifically refers to gas at standard conditions, so applying it to a liquid volume would be unusual and potentially misleading.

Why does my gas supplier use SCF instead of liters? SCF is a standard in the US gas industry because it normalizes gas volume to a fixed temperature and pressure, making it a consistent measure of gas quantity regardless of ambient conditions. Liters alone do not specify temperature and pressure, so they are ambiguous for gas without additional context.

Related

Formula used
in scf | Volume in SCF | SCF | 100 | 0
out l | Volume in liters | L | scf * 28.316846592 | 2
out m3 | Volume in cubic meters | m³ | l / 1000 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →