molecalculator

Moles & Molar Mass

Convert SCF to Gallons: Quick & Accurate Guide

Calculator No. 01-7220 · Updated · Formula and assumptions shown below

Liquid volume (gallons) 2.74 gal
Gas volume (SCF)
100 ft³
Set in the form below
Gas density at standard conditions
0.116 lb/ft³
Set in the form below
Liquid density
4.23 lb/gal
Set in the form below
You enter
Gas volume (SCF) (ft³), Gas density at standard conditions (lb/ft³), Liquid density (lb/gal)
You get
Liquid volume (gallons) (gal)
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

To convert standard cubic feet (SCF) of a gas to gallons of liquid, you must know the gas’s density at standard conditions and the liquid’s density. The formula is: gallons = (SCF × gas density in lb/ft³) ÷ (liquid density in lb/gal). For example, 100 SCF of propane (gas density 0.116 lb/ft³) converts to about 2.68 gallons of liquid propane (liquid density 4.23 lb/gal).

Formula

The conversion relies on mass conservation: the mass of gas equals the mass of liquid (assuming no loss during liquefaction). The formula is:

Gallons = (SCF × Gas Density) / Liquid Density

  • SCF – volume of gas at standard conditions (usually 60°F and 14.7 psia) in cubic feet.
  • Gas Density – mass per unit volume of the gas at those standard conditions (lb/ft³).
  • Liquid Density – mass per unit volume of the liquid at its boiling point or storage temperature (lb/gal).

Note that gas densities are often given at “standard” conditions, but different industries use different standards (e.g., 60°F vs. 15°C, 14.7 psia vs. 14.696 psia). Always confirm the reference conditions to avoid errors.

Worked Example

Using the calculator’s default values for propane:

  1. Gas volume: 100 SCF
  2. Gas density (propane at 60°F, 14.7 psia): 0.116 lb/ft³
  3. Liquid density (propane at 60°F): 4.23 lb/gal

Mass of gas = 100 × 0.116 = 11.6 lb

Volume of liquid = 11.6 ÷ 4.23 = 2.74 gallons (rounded to 2.74, but the calculator shows 2.74 with 2 decimals; actually 11.6/4.23 = 2.7423, so 2.74).

The calculator gives 2.74 gallons, matching this step-by-step calculation.

Assumptions

  • Standard conditions are 60°F and 14.7 psia (common in the US).
  • The gas behaves ideally (valid for most gases at low pressure).
  • No mass is lost during liquefaction (100% efficiency).
  • Liquid density is at the same temperature as the gas standard, or at the storage temperature specified.

Why Convert SCF to Gallons?

Engineers and technicians often need to compare gas volumes (billed in SCF) with liquid storage capacities (gallons). For example, a facility may receive propane as a liquid in tanks but use it as a gas. Knowing how many gallons of liquid will vaporize to a given SCF helps in sizing tanks, estimating runtimes, and planning deliveries. Similarly, cryogenic gases like nitrogen or oxygen are stored as liquids and used as gases; conversions are essential for supply chain management.

How to Find the Right Densities

You need accurate densities for your specific gas and liquid. Here’s where to look:

  • Gas density – Available from gas supplier data sheets, engineering handbooks, or online calculators. For common gases, standard densities are widely published (e.g., propane 0.116 lb/ft³, methane 0.0423 lb/ft³, nitrogen 0.0744 lb/ft³).
  • Liquid density – Also from supplier data or handbooks. Note that liquid density changes with temperature; use the value at your storage temperature. For propane at 60°F, it’s about 4.23 lb/gal; for liquid nitrogen at -320°F, it’s about 6.75 lb/gal.

If you don’t have the exact density, you can estimate using the ideal gas law for the gas (density = P×MW/(R×T)), but for liquids you need empirical data.

Common Mistakes and Misconceptions

A frequent error is using the gas density at non-standard conditions (e.g., at actual pressure and temperature) without adjusting to SCF. Another is confusing SCF with ACF (actual cubic feet). SCF is always at a defined standard, while ACF is at the actual pressure and temperature. Also, some people incorrectly use the liquid density in lb/ft³ instead of lb/gal; remember 1 gal = 0.13368 ft³, so multiply lb/ft³ by 0.13368 to get lb/gal.

Another misconception: SCF to gallons is not a direct volume conversion because gas and liquid have different densities. You cannot use a single conversion factor for all gases; it depends on the gas and its conditions.

Practical Applications and Examples

Let’s look at two real-world examples:

  • Propane tank sizing: A grill uses 20,000 SCF of propane per month. How many gallons of liquid propane is that? Using propane gas density 0.116 lb/ft³ and liquid density 4.23 lb/gal: 20,000 × 0.116 / 4.23 = 548 gallons. A typical 500-gallon tank would need refilling about monthly.
  • Nitrogen for industrial use: A lab uses 100,000 SCF of nitrogen gas per week. Liquid nitrogen density is about 6.75 lb/gal, gas density 0.0744 lb/ft³. So 100,000 × 0.0744 / 6.75 = 1,102 gallons of liquid nitrogen per week. This helps in ordering cryogenic dewars.

These examples show how the conversion helps in planning storage and procurement.

Limitations and Accuracy

The conversion assumes ideal gas behavior and constant densities. Real gases deviate at high pressures or low temperatures, but for most industrial gases at standard conditions, the error is under 1%. Liquid density varies with temperature; if you store the liquid at a different temperature than the density reference, adjust accordingly. Also, SCF standards vary: the US uses 60°F and 14.7 psia, but some international standards use 15°C and 101.325 kPa. Always verify which standard your SCF is based on.

For precise work, consult the gas supplier’s technical data or use a real-gas equation of state. But for most engineering estimates, the simple mass-based conversion is sufficient.

Frequently Asked Questions

Can I convert SCF to gallons without knowing the gas type?

No. Different gases have different densities, so the conversion factor varies. You must know the specific gas and its densities. If you only have the molecular weight, you can estimate the gas density using the ideal gas law at standard conditions, but you still need the liquid density.

What is the difference between SCF and ACF?

SCF (standard cubic feet) is the volume at a defined standard temperature and pressure (e.g., 60°F, 14.7 psia). ACF (actual cubic feet) is the volume at the actual pressure and temperature of the gas. To convert ACF to SCF, you use the ideal gas law to adjust for pressure and temperature differences.

Why does the calculator ask for gas density in lb/ft³ and liquid density in lb/gal?

Because SCF is in cubic feet and the result is in gallons. Using these units makes the formula straightforward: (SCF × lb/ft³) ÷ (lb/gal) = gallons. If you have densities in other units, convert them first.

Does temperature affect the conversion?

Yes. Gas density depends on temperature and pressure, and liquid density depends on temperature. The calculator uses fixed densities, so you should use values that match your actual conditions. If the gas is at a different temperature than the standard, you need to correct the gas density.

Can I use this conversion for cryogenic liquids like liquid oxygen?

Yes, the same formula applies. For liquid oxygen, gas density at standard conditions is about 0.0828 lb/ft³ and liquid density is about 9.5 lb/gal. Just plug in the correct densities. However, be aware that cryogenic liquids are stored at very low temperatures, so the liquid density is at that temperature, not at room temperature.

What if I only know the molecular weight of the gas?

You can calculate the gas density using the ideal gas law: density = (P × MW) / (R × T). At standard conditions (14.7 psia, 60°F = 519.67°R), R = 10.73 (psia·ft³)/(lb·mol·°R). For propane (MW=44.1), density = (14.7 × 44.1) / (10.73 × 519.67) = 0.116 lb/ft³. Then you still need the liquid density from a reference.

Related

Formula used
in scf | Gas volume (SCF) | ft³ | 100 | 0
in gd | Gas density at standard conditions | lb/ft³ | 0.116 | 0
in ld | Liquid density | lb/gal | 4.23 | 0
out gal | Liquid volume (gallons) | gal | scf * gd / ld | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →